Chemlife
- 873-1251 Chemlife® 24 Catalyst
- Product Codes:
873-1251 Catalyst
Product Specifications
| Viscosity: | Flash Point: | Density (Kg/L): | Solid (% by weight): | Solid (% by volume): | Shelf Life (months): |
|---|---|---|---|---|---|
N/A |
-4°C (39°F) | 0.87 ± 2% at 25°C | 15% | 9% | 6 |
Product Description
Designed as a fast catalyst for Chemlife 24 systems.
Uses
This product cannot be used alone. Refer to the Chemlife 24 technical bulletin.
For interior use only.
Environmental Data (as supplied)
| VOC less exempt lb/gal: | VOC lb/gal: | VOC less exempt g/l: | VOC g/l: | VOC lb/lb Solid: | VHAPs lb/lb Solid: |
|---|---|---|---|---|---|
| 6.17 | 6.17 | 740 | 740 | 5.61 | 0.49 |
Note:
See individual compliance sheets for specific data.
Application Data
| Suggested Uses: | Mixing Ratio: | Pot Life: | Application Viscosity: | Reducer: | Retarder: | Clean-up Solvent: | Recommended Wet Film: | Coverage: |
|---|---|---|---|---|---|---|---|---|
| N/A | As recommended on Product Information Sheets |
N/A | N/A |
N/A | N/A | Lacquer Thinner | N/A | N/A |
Note:
N/A
Directions for Use
Surface Preparation
N/A
General Information
Measure carefully and accurately before adding to products. Agitate when adding to recommended acid cured products.
Refer to Technical Bulletin of the Chemlife 24. Do not under-catalyze or over-catalyze with this product. Under catalyzation will result in slow curing or an inability of the coating to cure.Over-catalyzation will result in a brittle film.
Avoid contamination or contact ferrous metals. Use high-grade stainless steel or appropriate plastic equipment and parts.
This product is corrosive. Protect eyes and skin from contact or splash. In case of accident, wash immediately with plenty of water for 20 minutes and call a doctor.
THE CUSTOMER IS RESPONSIBLE FOR FOLLOWING THE RECOMMENDED APPLICATION PROCEDURES. FAILURE TO ADHERE TO THE RECOMMENDATIONS GIVEN IN THIS DATA SHEET WILL LIKELY RESULT IN UNSATISFACTORY FILM APPEARANCE OR FILM FAILURE. THE COMPLETE COATING SYSTEM SHOULD BE CHECKED FOR REQUIRED PROPERTIES PRIOR TO THE START-UP OF PRODUCTION.
Drying Times
At 20°C (Minimum Required)
| Tack Free Time: | Dry to Sand: | Dry to Stack: |
|---|---|---|
| N/A | N/A | N/A |
At 50°C (Minimum Required)
| Tack Free Time: | Dry to Sand: | Dry to Stack: |
|---|---|---|
| N/A | N/A | N/A |
Note:
N/A
Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.
These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.
Values shown are calculated estimates and should not be construed as product specifications. We cannot anticipate all conditions under which this information and our products or the products of other manufacturers in combination with our products may be used. We accept no responsibility for results obtained by the application of this information or the safety and suitability of each such product or product combination for their own purposes. Unless otherwise agreed in writing, we sell the products without warranty, and users assume all responsibility and liability for loss or damage arising from the use of our products whether used alone or a combination with other products. Use of unapproved or reclaimed solvent blends may reduce film properties and is not recommended.