Product Specifications

Viscosity:	Flash Point:	Density (Kg/L):	Solid (% by weight):	Solid (% by volume):	Shelf Life (months):
25º C 2100-2500 CPS#3 Brookfield	62ºC (144º F)	0.94	37.50 (+/- 1.00)	30.65 (+/- 1.00)	24

Product Description

Promatch FlexGlaze is a very unique glaze. Promatch FlexGlaze has extended open time for workability. Extended open times for enhanced work ability and ease of use. Promatch FlexGlaze is able to be topcoated quicker than industry standard products. It has the ability to be uniformly blended. Works well over Chemcraft pigmented products and clears (not to be used direct to wood as a stain). Promatch FlexGlaze is compatible with all Chemcraft products for distribution, excluding waterborne.

Uses

Promatch FlexGlaze can be used in the following interior applications:

Cabinetry

Furniture

Millwork

Recreational

Building Products

Environmental Data (as supplied)

VOC less exempt lb/gal:	VOC lb/gal:	VOC less exempt g/l:	VOC g/l:	VOC lb/lb Solid:	VHAPs lb/lb Solid:
4.9	4.9	575	575	1.42	0

Note:

N/A

Application Data

Suggested Uses:	Mixing Ratio:	Pot Life:	Application Viscosity:	Reducer:	Retarder:	Clean-up Solvent:	Recommended Wet Film:	Coverage:
To be used as a glaze only, under all Chemcraft distribution products (excluding Waterborne). Not to be used as a direct to wood stain.  Can be tinted with 866 series colorants. *Note - using 866 series colorants will increase VOCs.	N/A	N/A	N/A	801-1202	800-4310	Lacquer Thinner	N/A	Theoretical coverage - 12 m2/l (130 pi2/l) at 1 mil dry and at 100% efficiency.

Note:

Spray or brush and wipe.

Surface Preparation

Clean and sanded smooth with excess dust blown off.

Prior to use, mix Promatch FlexGlaze carefully and reduce viscosity by adding reducer as needed.  Apply the reduced Glaze by spraying or with a rag.  Allow two to three minutes air drying before wiping.  Wipe clean and do not leave on any excess material that may interfere with optimum adhesion.

General Information

FlexGlaze does not contain oil and is not combustible.

Can be tinted with 866 series colorants at a maximum of 10%.

Dry Time: Glaze must dry 30 minutes prior to apply topcoat if wiped very clean.  Glaze must dry 2 hours prior to applying topcoat if left heavy.

THE CUSTOMER IS RESPONSIBLE FOR FOLLOWING THE RECOMMENDED APPLICATION PROCEDURES. FAILURE TO ADHERE TO THE RECOMMENDATIONS GIVEN IN THIS DATA SHEET WILL LIKELY RESULT IN UNSATISFACTORY FILM APPEARANCE OR FILM FAILURE. THE COMPLETE COATING SYSTEM SHOULD BE CHECKED FOR REQUIRED PROPERTIES PRIOR TO THE START-UP OF PRODUCTION.

Drying Times

At 20°C (Minimum Required)

Tack Free Time:	Dry to Sand:	Dry to Stack:
N/A	N/A	N/A

At 50°C (Minimum Required)

Tack Free Time:	Dry to Sand:	Dry to Stack:
N/A	N/A	N/A

Note:

Glaze must dry 30 minutes prior to apply topcoat if wiped very clean. Glaze must dry 2 hours prior to applying topcoat if left heavy.

---

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.