Product Specifications

Viscosity:	Flash Point:	Density (Kg/L):	Solid (% by weight):	Solid (% by volume):	Shelf Life (months):
Zahn #2 signature cup 36 sec at 25°C	>93.3°C (200° F)	1.03	39 ± 1%	37 ± 1%	12

Product Description

Aqualux Uniclear Sealer is an all acrylic based formula developed to enhance the rich color of exotic woods like cherry, walnut, mahogany and others. Aqualux Uniclear Sealer is a high solid water white sealer designed for ease of application. Aqualux Uniclear Sealer is compatible with all Chemcraft Waterborne topcoats.

Uses

Aqualux Uniclear Sealer is designed for interior furniture, fittings, kitchen cabinet and other wood applications.

Environmental Data (as supplied)

VOC less exempt lb/gal:	VOC lb/gal:	VOC less exempt g/l:	VOC g/l:	VOC lb/lb Solid:	VHAPs lb/lb Solid:
1.79	0.87	216	105	0.26	0.00

Note:

See individual compliance sheets for specific data

Application Data

Suggested Uses:	Mixing Ratio:	Pot Life:	Application Viscosity:	Reducer:	Retarder:	Clean-up Solvent:	Recommended Wet Film:	Coverage:
Wood Sealer	N/A	N/A	Zahn #2 signature cup 36 seconds	Water as required	N/A	Use water when in liquid state, use water / Butyl Cellosolve 100-119 when material is semi-drie	4 - 5 mils wet	N/A

Note:

N/A

Surface Preparation

Substrate should be sanded using 120, 150 or 180 grit sandpaper prior to staining or coating. Aqualux Uniclear Sealer should be sanded with 240, 280, and 320 grit stearated paper prior to being coated. Stain systems recommended under this product are Chemcraft Waterborne wiping stains 824-XXXX.

General Information

Mix material before use. Add water to reduce, if required, and mix thoroughly. Apply by spray at wet film builds of 4 - 5 mils. Aqualux Uniclear can be used under 423-46XX. Application and drying conditions must be at temperatures of 18°C or above and at a humidity of less than 65%. Increased airflow and/or drying temperatures, including the use of infrared, will greatly decrease dry times.
Aqualux Uniclear Sealer must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces should be avoided.

Note: Aqualux Uniclear Sealer must not be polluted with oil, solvent based paint or the like and should not be applied to metal surfaces. Aqualux Uniclear Sealer must not be sanded with steel wool between the coats. Film build should not exceed 2 dry mils per coat. Total film build must not exceed 4 dry mils.

THE CUSTOMER IS RESPONSIBLE FOR FOLLOWING THE RECOMMENDED APPLICATION PROCEDURES. FAILURE TO ADHERE TO THE RECOMMENDATIONS GIVEN IN THIS DATA SHEET WILL LIKELY RESULT IN UNSATISFACTORY FILM APPEARANCE OR FILM FAILURE. THE COMPLETE COATING SYSTEM SHOULD BE CHECKED FOR REQUIRED PROPERTIES PRIOR TO THE START-UP OF PRODUCTION.

Drying Times

At 20°C (Minimum Required)

Tack Free Time:	Dry to Sand:	Dry to Stack:
15 - 20 minutes	1 hour	24 hours

At 50°C (Minimum Required)

Tack Free Time:	Dry to Sand:	Dry to Stack:
10 - 15 minutes	45 minutes	8 hours

Note:

N/A

---

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.