Product Specifications

Viscosity:	Flash Point:	Density (lb/gal):	Solid (% by weight):	Solid (% by volume):	Shelf Life (months):
N/A	80°F (<7°)	7.5 – 8.9	9 - 30%	6 - 24%	24

Product Description

Promatch C-Mix Stains 825-91XX are all-purpose wipe stains for furniture and cabinets. They should be mixed well due to the heavy concentration of pigments. Application may be by hand or spray. Stains are intermixable and/or reducible. Promatch C-Mix Stains 825-91XX offer a simple one step stain color base with good clarity and grain fill and ease of workability. Extra colorant can be added to any of the colors. Consult your local representative for directions.

Uses

As a stain for interior wood application.

Environmental Data (as supplied)

VOC less exempt lb/gal:	VOC lb/gal:	VOC less exempt g/l:	VOC g/l:	VOC lb/lb Solid:	VHAPs lb/lb Solid:
6.4 – 7.11	6.4 – 7.11	750 - 833	750 - 833	2.25 – 9.8	<0.1

Note:

N/A

Application Data

Suggested Uses:	Mixing Ratio:	Pot Life:	Application Viscosity:	Reducer:	Retarder:	Clean-up Solvent:	Recommended Wet Film:	Coverage:
Wood Stain	N/A	N/A	N/A	825-9000	800-4310 (5 to 15 % by volume)	Lacquer Thinner	N/A	N/A

Note:

N/A

Surface Preparation

Wood substrate should be sanded with 120, 150 or 180 grit paper prior to staining or coating. On woods such as maple, coarser sanding, such as 150 grit, should be performed to avoid polishing of the wood surface. Hand sanding in the direction of the grain following orbital sanding will remove swirl marks.

General Information

Application may be by hand or spray. These stains must be wiped into the grain and wiped clean with a clean rag to ensure good adhesion by subsequent clear coats. If the stain is too dark, the color strength may be reduced using Promatch C-Mix Stain Base 825-9000. 

Promatch 825-91XX can be tinted with Chemcraft 825-92XX tints along with universal tints like the 844 and 866 quality. The maximum recommended amount of tints to add to the stain base is:

825-92XX tints 10-15% by volume, 844 and 866 universal tints 3-5% by volume.                                                                                       (Depending on the colors consult your local representative)

These products may be clear coated with any of the following systems: All pre-catalyzed lacquer, post-catalyzed lacquer, varnish and ora Verde from Chemcraft as well as the sealers associated with these systems. 

All 825-91XX colors are acid stable. They will not change color when an acid cured Chemcraft product is used to seal and topcoat them.

These stains demonstrate good open time to allow for uniform appearance on large pieces.

Product must be thoroughly agitated before use. 

 

THE CUSTOMER IS RESPONSIBLE FOR FOLLOWING THE RECOMMENDED APPLICATION PROCEDURES. FAILURE TO ADHERE TO THE RECOMMENDATIONS GIVEN IN THIS DATA SHEET WILL LIKELY RESULT IN UNSATISFACTORY FILM APPEARANCE OR FILM FAILURE. THE COMPLETE COATING SYSTEM SHOULD BE CHECKED FOR REQUIRED PROPERTIES PRIOR TO THE START-UP OF PRODUCTION.

Drying Times

Room Temperature (68°F)

Tack Free Time:	Dry to Sand:	Dry to Stack:
N/A	N/A	N/A

Forced Drying Schedule (122°F)

Tack Free Time:	Dry to Sand:	Dry to Stack:
N/A	N/A	N/A

Note:

Drying time prior to sealer application is 45 to 60 minutes.

---

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.