Product Specifications

Viscosity:	Flash Point:	Density (lb/gal):	Solid (% by weight):	Solid (% by volume):	Shelf Life (months):
Zahn #3 signature cup 45 sec at 77°F	21°F	10.5	58%	39%	12

Product Description

Bianco is our pigmented polyurethane system; Bianco PU Basecoat Neutral is a universal primer designed to be used in conjunction with our ora Verde® line topcoats. Durable and flexible, it can be used as tinted primer to achieve deep, dark and rich colors. Builds quickly to help you achieve a high end look when your need is for an opaque color.

Uses

Developed for use in the high end kitchen cabinet market. Its durability will also allow for use in store fixture applications.

Environmental Data (as supplied)

VOC less exempt lb/gal:	VOC lb/gal:	VOC less exempt g/l:	VOC g/l:	VOC lb/lb Solid:	VHAPs lb/lb Solid:
<4.4	<4.4	<530	<530	<0.72	<0.17

Note:

N/A

Application Data

Suggested Uses:	Mixing Ratio:	Pot Life:	Application Viscosity:	Reducer:	Retarder:	Clean-up Solvent:	Recommended Wet Film:	Coverage:
Wood Finish	100 Parts 536-1255 with 50 Parts 876-9068 (by volume)	2 Hours	Zahn #2 signature cup 30 seconds	Fast 803-1410, Medium 803-1409, or slow 803-1408 if needed	800-5328 3-5% by volume	800-5500 Acetone	3 to 5 wet mils	N/A

Note:

MAXIMUN DRY FILM THICKNESS OF THE SYSTEM MUST NOT EXCEED 6.0 DRY MILS

Surface Preparation

Substrate must be sanded using 120, 150 or 180 grit paper prior to priming. Basecoat should be sanded with 280/320 grit paper prior to being coated. The Basecoat should be coated within eight hours of being sanded. Appropriate topcoat is the ora Verde Bianco 109-48XX, or ora Verde Chiaro 436-48XX. When recoating, the previous coat must be sanded and the next coat applied within eight hours.

General Information

The mixed product contains 876-9068, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detailed information.

Product must be thoroughly stirred before adding the hardener in the recommended ratio. The viscosity of the product should be monitored after mixing with the hardener.

The relative humidity in the application and drying room must not exceed 75% for maximum coating performance.  The hardener must not be exposed to water or solvents containing alcohol.

 

THE CUSTOMER IS RESPONSIBLE FOR FOLLOWING THE RECOMMENDED APPLICATION PROCEDURES. FAILURE TO ADHERE TO THE RECOMMENDATIONS GIVEN IN THIS DATA SHEET WILL LIKELY RESULT IN UNSATISFACTORY FILM APPEARANCE OR FILM FAILURE. THE COMPLETE COATING SYSTEM SHOULD BE CHECKED FOR REQUIRED PROPERTIES PRIOR TO THE START-UP OF PRODUCTION.

Drying Times

Room Temperature (68°F)

Tack Free Time:	Dry to Sand:	Dry to Stack:
20 minutes	2 hours	24 hours

Forced Drying Schedule (122°F)

Tack Free Time:	Dry to Sand:	Dry to Stack:
10 minutes @ room temperature	15 minutes @ 110°F	15 minutes @ 140°F

Note:

N/A

---

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.