Selva Pro
- 536-1700 Selva™ Pro Bianco Polyurethane HS White Primer
- Product Codes:
536-1700
Product Specifications
| Viscosity: | Flash Point: | Density (lb/gal): | Solid (% by weight): | Solid (% by volume): | Shelf Life (months): |
|---|---|---|---|---|---|
60-65 KU |
45° F | 11.15 | 65.1 | 46.3 | 24 |
Product Description
our high-build, fast-drying Selva Pro Bianco HS White PU Primer provides exceptional sandability and is perfect for achieving a premium opaque finish. It can be tinted with 844 tints to create a wide range of pastel shades, allowing versatility for various design needs. With its quick-build properties, this primer helps you achieve a refined, high-end look effortlessly.
Uses
Ideal for high-end kitchen and bathroom cabinetry, as well as a wide range of interior wood applications, including architectural millworks, store fixtures, and office furniture.
Environmental Data (as supplied)
| VOC less exempt lb/gal: | VOC lb/gal: | VOC less exempt g/l: | VOC g/l: | VOC lb/lb Solid: | VHAPs lb/lb Solid: |
|---|---|---|---|---|---|
| 3.89 | 3.89 | 465.5 | 465.5 | 0.53 | 0.32 |
Note:
N/A
Application Data
| Suggested Uses: | Mixing Ratio: | Pot Life: | Application Viscosity: | Reducer: | Retarder: | Clean-up Solvent: | Recommended Wet Film: | Coverage: |
|---|---|---|---|---|---|---|---|---|
| Wood Finishes | 100 Parts 536-1700 with 50 Parts 876-9700 (by volume) |
2-3 hours | Zahn #2 signature cup 24-26 seconds. |
803-2000 | 800-2001 3-5% by volume | 800-5500 Acetone | 4-6 wet mils | N/A |
Note:
MAXIMUM DRY FILM THICKNESS OF THE SYSTEM MUST NOT EXCEED 8 DRY MILS
Directions for Use
Surface Preparation
Substrate must be sanded using 120, 150 or 180 grit paper prior to priming. Primer should be sanded with 320 grit paper prior to being coated. The Primer should be coated within eight hours of being sanded. Appropriate topcoats are the Selva Pro Bianco 109-17XX / 109-19XX or Selva Pro Acrilico 109-47XX / 109-46XX. When recoating, the previous coat must be sanded and the next coat applied within eight hours.
General Information
THE CUSTOMER IS RESPONSIBLE FOR FOLLOWING THE RECOMMENDED APPLICATION PROCEDURES. FAILURE TO ADHERE TO THE RECOMMENDATIONS GIVEN IN THIS DATA SHEET WILL LIKELY RESULT IN UNSATISFACTORY FILM APPEARANCE OR FILM FAILURE. THE COMPLETE COATING SYSTEM SHOULD BE CHECKED FOR REQUIRED PROPERTIES PRIOR TO THE START-UP OF PRODUCTION.
Drying Times
Room Temperature (68°F)
| Tack Free Time: | Dry to Sand: | Dry to Stack: |
|---|---|---|
| 20 minutes | 1 hour | 24 hours |
Forced Drying Schedule (122°F)
| Tack Free Time: | Dry to Sand: | Dry to Stack: |
|---|---|---|
| 10 minutes | 15 minutes | 1 hour |
Note:
N/A
Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.
These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.
Values shown are calculated estimates and should not be construed as product specifications. We cannot anticipate all conditions under which this information and our products or the products of other manufacturers in combination with our products may be used. We accept no responsibility for results obtained by the application of this information or the safety and suitability of each such product or product combination for their own purposes. Unless otherwise agreed in writing, we sell the products without warranty, and users assume all responsibility and liability for loss or damage arising from the use of our products whether used alone or a combination with other products. Use of unapproved or reclaimed solvent blends may reduce film properties and is not recommended.