Product Specifications

Viscosity:	Flash Point:	Density (lb/gal):	Solid (% by weight):	Solid (% by volume):	Shelf Life (months):
Zahn #2 signature cup 28-33 sec at 77°F	-4°F (-20°C)	9.7	42.8%	23.7%	12

Product Description

Versaprime is a one-component, high solids, pre-catalyzed lacquer used as a primer. This pigmented pre-catalyzed primer provides chemical resistance along with adhesion over all wood species. 545-5119 Versaprime can be used with 131-11XX E.S. Lacquer White and 131-70XX Variset® Pigmented Topcoat. The coating is supplied at a ready to spray viscosity.  

Uses

Versaprime is recommended for use as a primer for kitchen cabinets, office and household furniture as well as many other interior wood applications. It has good filling properties and hiding characteristics. Versaprime is a pure white primer with excellent sandability.

Environmental Data (as supplied)

VOC less exempt lb/gal:	VOC lb/gal:	VOC less exempt g/l:	VOC g/l:	VOC lb/lb Solid:	VHAPs lb/lb Solid:
<5.26	<4.85	<632	<582	<1.21	<0.43

Note:

See individual compliance sheets for specific data

Application Data

Suggested Uses:	Mixing Ratio:	Pot Life:	Application Viscosity:	Reducer:	Retarder:	Clean-up Solvent:	Recommended Wet Film:	Coverage:
Wood Primer	100 parts 545-5119 to 3 parts 873-0870 (as a post-cat)	12 hours	Zahn #2 signature cup 28 – 33 seconds	803-1325	N/A	803-1298 or 800-5500	3 – 5 mils	409 sq. ft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Note:

N/A

Surface Preparation

Substrate should be sanded using 120, 150 or 180 grit stearated papers prior to coating. Primers, if used, should be sanded with 280/320 grit stearated paper prior to being coated. When recoating the previous coat of Versaprime must be sanded and the next coat applied within eight hours. Versaprime cannot be used on metal, old oil or cellulose lacquers. 

General Information

Agitate material before use.  Always mix Versaprime while adding catalyst and reducers in the recommended mixing ratios.  Versaprime must be agitated thoroughly at all times to ensure product consistency.

Apply at 3 – 5 mils wet sanded substrate.  Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper.  The second and subsequent coats must be applied the same day as the previous coat is sanded.

Maximum film build of Versaprime should not exceed 2 – 3 mils dry. 

Maximum film build of total coating system must not exceed 4 mils dry. 

Contact with metal surfaces should be avoided. Versaprime must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats. Versaprime must not be used and dried at temperatures below 64°F or relative humidity above 65%. 

During the curing process, the coating must not be exposed to ammonia vapors.  Ammonia cleaners should not be used for cleaning the finish surfaces.  This may accelerate discoloration.

THE CUSTOMER IS RESPONSIBLE FOR FOLLOWING THE RECOMMENDED APPLICATION PROCEDURES. FAILURE TO ADHERE TO THE RECOMMENDATIONS GIVEN IN THIS DATA SHEET WILL LIKELY RESULT IN UNSATISFACTORY FILM APPEARANCE OR FILM FAILURE. THE COMPLETE COATING SYSTEM SHOULD BE CHECKED FOR REQUIRED PROPERTIES PRIOR TO THE START-UP OF PRODUCTION.

Drying Times

Room Temperature (68°F)

Tack Free Time:	Dry to Sand:	Dry to Stack:
5 - 8 minutes	10 - 15 minutes	1 hour

Forced Drying Schedule (122°F)

Tack Free Time:	Dry to Sand:	Dry to Stack:
Flash off before entering oven	5 - 8 minutes	30 minutes

Note:

N/A

---

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.