VARISET Pigmented Primer

545-8023 Variset® Pre-Cat Pigmented Primer

Product Codes:

545-8023

Surface Preparation:

Substrate should be sanded using 120, 150 or 180 grit stearated paper prior to coating. Variset Primer should be sanded with 280/320 grit stearated paper prior to being coated and the next coat must be applied within eight hours of sanding. Variset Primer cannot be used on metal, old oil or cellulose lacquers.

General Information:

Agitate material before use. Always mix Variset Primer while adding catalyst and reducers in the recommended mixing ratio. Variset Primer must be agitated thoroughly at all times to ensure product consistency.

Apply at 3 – 5 mils wet sanded substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper.

Maximum film build of Variset Primer should not exceed 2 – 3 mils dry. Maximum film build of total coating system must not exceed 4 mils dry. Contact with metal surfaces should be avoided.

Variset Primer must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats.

Variset Primer must not be used and dried at temperatures below 64°F or relative humidity above 65%. During the curing process, the coating must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finish surfaces. This may accelerate discoloration.

PDF Name: US-PIS_545-8023_Variset_Pre-Cat_Pigmented_Primer

Tack Free Time: 10 - 15 minutes

Files: US-PIS_545-8023_Variset_Pre-Cat_Pigmented_Primer.pdf

Dry to Sand : 45 - 60 minutes

Dry to Stack: 3 hours

Tack Free Time: Flash off before entering oven

Dry to Sand: 20 - 30 minutes

Dry to Stack: 60 - 90 minutes

Note: N/A

spec_description:

Variset Primer is a one-component, high solids, pre-catalyzed Reactive Amino Coating (RAC). This product is formulated using the same chemistry as Varicure^® with easy sand and great build. Variset Primer comes in a ready to use format, there is no need for reduction. This pigmented pre-catalyzed RAC has very low odor during the curing process. Variset Primer is also HAPs solvent free.

spec_uses:

Variset Primer is recommended for use as a primer for Variset and Variset Plus. It has good filling properties and hiding characteristics.

VOC less exempt: <4.80

VOC lb/gal: <4.07

VOC less exempt g/l: <575

VOC g/l: <488

VOC lb/lb Solid: <0.95

VHAPs lb/lb Solid: <0.00

Note:

See individual compliance sheets for specific data

Suggested Uses:

Wood Primer

Mixing Ratio:

100 parts 545-8023 to 3 parts 873-0870 (if use as a post-catalyzed primer)

Pot Life:

8 hours

Application Viscosity:

Zahn #2 signature cup 25 - 30 seconds

Reducer: 803-1325

Retarder: N/A

Clean-up Solvent: 803-1298 or 800-5500

Recommended Wet Film: 3 – 5 mils

Coverage:

545 sq. ft. /gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 27 sec at 77°F

Flash Point: -4°F (-20°C)

Density (lb/gal): 9.51

Solid (% by weight): 47.1%

Solid (% by volume): 28%

Shelf Life (months): 6

VARISET Pigmented Primer

545-8023 Variset® Pre-Cat Pigmented Primer

Find distributor Trouver un distributeur

spec_description:

BACK

VARISET Pigmented Primer

545-8023 Variset® Pre-Cat Pigmented Primer

spec_description:

Product codeCodes de produit
Product Codes:

545-8023

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 27 sec at 77°F

Flash Point: -4°F (-20°C)

Density (lb/gal): 9.51

Solid (% by weight): 47.1%

Solid (% by volume): 28%

Shelf Life (months): 6

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_545-8023_Variset_Pre-Cat_Pigmented_Primer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap