Butyl Cellosolve

800-5742 Butyl Cellosolve (100-119) (013-0500)

Product Codes:

800-5742 Butyl Cellosolve

Surface Preparation:

N/A

General Information:

N/A

PDF Name: CA-PIS_800-5742_Butyl_Cellosolve_(100-119)_(013-0500)

Tack Free Time: N/A

Dry to Sand : N/A

Dry to Stack: N/A

Tack Free Time: N/A

Dry to Sand: N/A

Dry to Stack: N/A

Note: N/A

spec_description:

Butyl Cellosolve is a glycol ether with a very slow evaporation rate. Butyl Cellosolve is also referred to as Glycol Ether EB or 2-Butoxyethanol.

spec_uses:

Retarder solvent for nitrocellulose containing coatings used when severe blushing due to extreme humidity is experienced. As this solvent significantly slows the drying time, it is recommended to start with an addition of 1% of the solvent and not exceed 3%. If the blushing problem persists, contact your AkzoNobel representative.

VOC less exempt lb/gal: 7.51

VOC lb/gal: 7.51

VOC less exempt g/l: 900

VOC g/l: 900

VOC lb/lb Solid: 0.00

VHAPs lb/lb Solid: 0.00

Note:

See individual compliance sheets for specific data.

Suggested Uses: N/A

Mixing Ratio:

1 - 3% maximum

Pot Life: N/A

Application Viscosity:

N/A

Reducer: N/A

Retarder: N/A

Clean-up Solvent: N/A

Recommended Wet Film: N/A

Coverage:

N/A

Note application:

N/A

Viscosity:

N/A

Flash Point: 65°C

Density (lb/gal): 0.90 ± 2% at 25°C

Solid (% by weight): 0%

Solid (% by volume): 0%

Shelf Life (months): Unlimited

Butyl Cellosolve

800-5742 Butyl Cellosolve (100-119) (013-0500)

Find distributor

spec_description:

Butyl Cellosolve is a glycol ether with a very slow evaporation rate. Butyl Cellosolve is also referred to as Glycol Ether EB or 2-Butoxyethanol.

Back

Butyl Cellosolve

800-5742 Butyl Cellosolve (100-119) (013-0500)

spec_description:

Butyl Cellosolve is a glycol ether with a very slow evaporation rate. Butyl Cellosolve is also referred to as Glycol Ether EB or 2-Butoxyethanol.

Product code
Product Codes:

800-5742 Butyl Cellosolve

Product information

Product specifications

Viscosity:

N/A

Flash Point: 65°C

Density (lb/gal): 0.90 ± 2% at 25°C

Solid (% by weight): 0%

Solid (% by volume): 0%

Shelf Life (months): Unlimited

Uses

Environmental data (as supplied)

Application data

Surface Preparation

General Information

Drying Times

Find distributor

Download product information sheets

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

À propos de notre marque	Produits	Distributeurs	Utilisation
Nous contacter	Produits Pré-Catalysés	Nos distributeurs	Tutoriels vidéo
	Produits Post-Catalysés	Portail de commande de revêtements pour bois	Guide de résolution des problèmes
	Systèmes en polyuréthane		Glossaire
	Systèmes de couleur		Spécifications techniques
	Produits vinylique		Application mobile
	Nitrocellulose
	Spécialisés

Témoins	Paramètres des témoins	Confidentialité	Plan du site