VARICURE SELECT Topcoat

431-52XX VARICURE® SELECT Pre-Cat Clear TC

Codes de produit:

431-5205 Flat
431-5210 Matte
431-5220 Low Gloss
431-5235 Satin
431-5250 Semi-Gloss
431-5290 High Gloss

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit stearated paper prior to staining or coating. Sealers, if used, should be sanded with 280/320 grit stearated paper prior to being coated. The sealer should be topcoated within eight hours of being sanded. When recoating, the previous coat of Varicure Select must be sanded and the next coat applied within eight hours. VARICURE SELECT Clear Topcoat cannot be used on metal, old oil or cellulose lacquers. Stain systems used under acid catalyzed systems should be acid stable. AkzoNobel recommends using 825-90XX or 825-91XX Promatch® C-Mix Stains.

General Information:

Agitate material before use. Always mix VARICURE SELECT Clear Topcoat while adding reducers in the recommended mixing ratios. VARICURE SELECT Clear Topcoat must be agitated thoroughly at all times to ensure product consistency and consistent gloss.

Apply at 3 – 5 mill wet on sanded substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper. The second and subsequent coats must be applied the same day as the previous coat is sanded. The maximum film build of VARICURE SELECT Clear Topcoat should not exceed 4 mils dry. This product is intended as a selfseal product; however, if a sealer is desired VARICURE SELECT Sealer 431-5201.

Maximum film build of total coating system must not exceed 4 mils dry. Contact with metal surfaces should be avoided.

VARICURE SELECT Clear Topcoat must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats. VARICURE SELECT Clear Topcoat must not be used and dried at temperatures below 18°C or relative humidity above 65%. During hardening the VARICURE SELECT Clear Topcoat must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finished surface. This may accelerate discoloration.

This product does contain formaldehyde, but the quantity is below the reportable amount according to OSHA regulation 1910.1048.

PDF Name: CA-PIS_431-52XX_VARICURE_SELECT_Pre-Cat_Clear_TC

Sec au toucher: 10 – 20 minutes

Files: CA-PIS_431-52XX_VARICURE_SELECT_Pre-Cat_Clear_TC.pdf

Sec au ponçage: 45 - 60 minutes

Sec à l'empilage: 2 Hours

Sec au toucher: Flash off before entering oven

Sec au ponçage: 15 – 20 minutes

Sec à l'empilage: 60 – 90 minutes

Remarque: N/A

spec_description:

VARICURE SELECT Clear Topcoat is a one-component high solids pre-catalyzed Reactive Amino Coating (RAC). This is a fast building pre-catalyzed RAC due to its high volume solids (24%). VARICURE SELECT Clear Topcoat demonstrates excellent moisture, household wear, household chemical, solvent and mar resistance. It exceeds the current Pre-Cat industry standards for chemical and moisture resistance - the type of performance you usually only find in higher performance technologies.

Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards.
Recommended: Architectural Woodwork Institute (AWI). System 2.

spec_uses:

VARICURE SELECT Clear Topcoat is recommended for office and household furniture, kitchen cabinets, as well as many other interior wood applications.

COV moins exemption lb/gal: <5.17

COV lb/gal: <4.60

COV moins exemption g/L: <620

COV g/L: <550

COV Kg/Kg solides: <1.9

VHAPs Kg/Kg solides: <0.50

Remarque:

N/A

Utilisations suggérées: Wood Finish

Catalyseur:

N/A

Vie en pot: N/A

Viscosité d'application:

Zahn #2 signature cup 21 – 23 seconds

Diluant: 121-803 or 121-8020

Retardateur: 800-5328 EEP

Solvant de nettoyage: Lacquer thinner

Épaisseur du film à l'application recommandée: 3 – 5 mils

Pouvoir couvrant:

391 sq. ft./gal (9 m²/l) at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Remarque:

N/A

Viscosité:

Zahn #2 signature cup 23 sec at 25° C

Point d'éclair: -4°F (-20°C)

Densité (kg/L): 0.93

Solides (% en poids): 31%

Solides (% en volume): 24%

Stabilité à l'entreposage (mois): 6

VARICURE SELECT Topcoat

431-52XX VARICURE® SELECT Pre-Cat Clear TC

Find distributor Trouver un distributeur

spec_description:

Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards.
Recommended: Architectural Woodwork Institute (AWI). System 2.

BACK

VARICURE SELECT Topcoat

431-52XX VARICURE® SELECT Pre-Cat Clear TC

spec_description:

Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards.
Recommended: Architectural Woodwork Institute (AWI). System 2.

Product codeCodes de produit
Codes de produit:

431-5205 Flat
431-5210 Matte
431-5220 Low Gloss
431-5235 Satin
431-5250 Semi-Gloss
431-5290 High Gloss

Informations sur le produit

Product specificationsSpécifications du produit

Viscosité:

Zahn #2 signature cup 23 sec at 25° C

Point d'éclair: -4°F (-20°C)

Densité (kg/L): 0.93

Solides (% en poids): 31%

Solides (% en volume): 24%

Stabilité à l'entreposage (mois): 6

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Télécharger les fiches d'information sur les produits

Files: CA-PIS_431-52XX_VARICURE_SELECT_Pre-Cat_Clear_TC.pdf

Ces produits sont uniquement conçus pour un usage industriel. AkzoNobel considère la sécurité comme une priorité absolue. Veuillez vous reporter à la fiche de données de sécurité pour plus d'informations sur l'utilisation sécuritaire de ce produit.

L'épaisseur du feuil, la porosité du substrat, le mouvement de l'air, la chaleur et l'humidité ont une forte incidence sur les temps de séchage. Les températures sont basées sur la température réelle du panneau de bois. Le temps de séchage peut varier en fonction du temps nécessaire pour que les panneaux de bois atteignent ces températures. La température de durcissement minimale de 18 °C/64 °F doit être maintenue pendant tout le cycle de durcissement afin d'obtenir l'intégrité de revêtement indiquée dans les caractéristiques du produit.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

À propos de notre marque	Produits	Distributeurs	Utilisation
Nous contacter	Produits Pré-Catalysés	Nos distributeurs	Tutoriels vidéo
	Produits Post-Catalysés	Portail de commande de revêtements pour bois	Guide de résolution des problèmes
	Systèmes en polyuréthane		Glossaire
	Systèmes de couleur		Spécifications techniques
	Produits vinylique		Application mobile
	Nitrocellulose
	Spécialisés

Témoins	Paramètres des témoins	Confidentialité	Plan du site