Lustrate

634-794 Lustrate White PU Pigmented Topcoat

Product Codes:

634-794 High Gloss

Surface Preparation:

Primer should be well sanded using 240, 320 and 360 grit stearated paper. Suitable primers are polyurethane (283-XXX) or polyester (740-XXX) types. Care should be taken during sanding to avoid sanding through the primer.

General Information:

Mix the desired amount of material and apply 4-6 mils wet. The high gloss coating, when cured, is very suitable to be buffed and polished where dust free conditions are not available.
The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the mixed material should be monitored regularly to maintain a consistent appearance.
The mixed product contains 876-9081, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials.
Total recommended film thickness of Lustrate is not to exceed 6 mils dry.

Primers to use under 634-794: polyurethane 283-3XX or polyester 740-XXX.

PDF Name: CA-PIS_634-794_Lustrate_White_PU_Pigmented_Topcoat

Tack Free Time: 15 - 30 minutes

Files: CA-PIS_634-794_Lustrate_White_PU_Pigmented_Topcoat.pdf

Dry to Sand : Overnight

Dry to Stack: Overnight

Tack Free Time: Flash off before entering oven

Dry to Sand: 3 hours

Dry to Stack: 4 hours

Note: N/A

spec_description:

Lustrate White is a two component polyurethane enamel with a tough cross linked film. The coating is very resistant to scratching and household chemicals when cured, and can provide exceptional gloss.

spec_uses:

Lustrate is used whenever premium performance characteristics are required for interior wood finishing.

VOC less exempt lb/gal: 3.39

VOC lb/gal: 3.39

VOC less exempt g/l: 407

VOC g/l: 407

VOC lb/lb Solid: 0.45

VHAPs lb/lb Solid: 0.28

Note:

See individual compliance sheets for specific data

Suggested Uses: Spray

Mixing Ratio:

1:1 with 876-9081

Pot Life:

3 hours

Application Viscosity:

Zahn #2 signature cup 20-25 seconds

Reducer: 121-834 or 800-5301

Retarder: 800-5328 EEP

Clean-up Solvent: Lacquer Thinner (do not mix with product)

Recommended Wet Film: 4-6 wet mils

Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #3 signature cup 35 sec at 25°C

Flash Point: 27°C (80°F)

Density (lb/gal): 1.36

Solid (% by weight): 69%

Solid (% by volume): 55%

Shelf Life (months): 12

Lustrate

634-794 Lustrate White PU Pigmented Topcoat

Find distributor

spec_description:

Back

Lustrate

634-794 Lustrate White PU Pigmented Topcoat

spec_description:

Product code
Product Codes:

634-794 High Gloss

Product information

Product specifications

Viscosity:

Zahn #3 signature cup 35 sec at 25°C

Flash Point: 27°C (80°F)

Density (lb/gal): 1.36

Solid (% by weight): 69%

Solid (% by volume): 55%

Shelf Life (months): 12

Uses

Environmental data (as supplied)

Application data

Surface Preparation

General Information

Drying Times

Find distributor

Download product information sheets

Files: CA-PIS_634-794_Lustrate_White_PU_Pigmented_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

À propos de notre marque	Produits	Distributeurs	Utilisation
Nous contacter	Produits Pré-Catalysés	Nos distributeurs	Tutoriels vidéo
	Produits Post-Catalysés	Portail de commande de revêtements pour bois	Guide de résolution des problèmes
	Systèmes en polyuréthane		Glossaire
	Systèmes de couleur		Spécifications techniques
	Produits vinylique		Application mobile
	Nitrocellulose
	Spécialisés

Témoins	Paramètres des témoins	Confidentialité	Plan du site