Catlac

131-50XX Catlac White Pre-Cat Pigmented Topcoat

Product Codes:

131-5015 15° Low Gloss
131-5020 20° Low Gloss
131-5035 35° Satin
131-5050 50° Semi-Gloss

Surface Preparation:

Before application of Catlac White, the basecoat must be sanded using 280/320 grit paper and free of dust and all contaminants. This product must not be applied over metal, old finish or nitrocellulose lacquer.

General Information:

Keep under mixing to assure consistency of the product. Apply 3 to 5 wet mils on sanded surface. One extra coat can be applied following a complete cure and a sanding with a 280/320 paper. Avoid all contact with metallic surfaces. Maximum film build of the topcoat should not exceed 2 mils dry. Maximum film build of the system should not exceed 4 mils dry.

To obtain complete cure, system should be applied at a temperature above 18°C and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surfaces must not be cleaned with ammonia containing products. Always use plastic or stainless equipment to eliminate discoloration due to oxidation.

Basecoats to use with 131-50XX: 225-0010, 522-1624, 545-8016, 546-7257

PDF Name: CA-PIS_131-50XX_Catlac_White_Pre-Cat_Pigmented_Topcoat

Tack Free Time: 15 - 20 minutes

Files: CA-PIS_131-50XX_Catlac_White_Pre-Cat_Pigmented_Topcoat.pdf

Dry to Sand : 45 - 60 minutes

Dry to Stack: 12 hours

Tack Free Time: Flash off before entering oven

Dry to Sand: 30 - 45 minutes

Dry to Stack: 60 - 90 minutes

Note: N/A

spec_description:

Quick drying pre-catalyzed white lacquer offering good yellowing and chemical resistance.

spec_uses:

Used as a protective coatings for wood. For interior uses only.

VOC less exempt lb/gal: 4.56

VOC lb/gal: 4.27

VOC less exempt g/l: 623

VOC g/l: 547

VOC lb/lb Solid: 11.59

VHAPs lb/lb Solid: 0.07

Note:

See individual compliance sheets for specific data

Suggested Uses:

Spray

Mixing Ratio:

N/A

Pot Life: N/A

Application Viscosity:

22-24 sec Zahn #2 at 25°C

Reducer: 121-803 or 121-8020 if needed

Retarder: 800-5328 if needed

Clean-up Solvent: Lacquer Thinner

Recommended Wet Film: 3 to 5 mils wet

Coverage:

9 m²/l (95 pi²/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 23 sec at 25°C

Flash Point: -20°C

Density (lb/gal): 0.99 ± 2% at 25°C

Solid (% by weight): 35%

Solid (% by volume): 22%

Shelf Life (months): 6

Catlac

131-50XX Catlac White Pre-Cat Pigmented Topcoat

Find distributor

spec_description:

Quick drying pre-catalyzed white lacquer offering good yellowing and chemical resistance.

Back

Catlac

131-50XX Catlac White Pre-Cat Pigmented Topcoat

spec_description:

Quick drying pre-catalyzed white lacquer offering good yellowing and chemical resistance.

Product code
Product Codes:

131-5015 15° Low Gloss
131-5020 20° Low Gloss
131-5035 35° Satin
131-5050 50° Semi-Gloss

Product information

Product specifications

Viscosity:

Zahn #2 signature cup 23 sec at 25°C

Flash Point: -20°C

Density (lb/gal): 0.99 ± 2% at 25°C

Solid (% by weight): 35%

Solid (% by volume): 22%

Shelf Life (months): 6

Uses

Environmental data (as supplied)

Application data

Surface Preparation

General Information

Drying Times

Find distributor

Download product information sheets

Files: CA-PIS_131-50XX_Catlac_White_Pre-Cat_Pigmented_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

À propos de notre marque	Produits	Distributeurs	Utilisation
Nous contacter	Produits Pré-Catalysés	Nos distributeurs	Tutoriels vidéo
	Produits Post-Catalysés	Portail de commande de revêtements pour bois	Guide de résolution des problèmes
	Systèmes en polyuréthane		Glossaire
	Systèmes de couleur		Spécifications techniques
	Produits vinylique		Application mobile
	Nitrocellulose
	Spécialisés

Témoins	Paramètres des témoins	Confidentialité	Plan du site