DANSEAL Sealer

432-1220 Danseal Post-Cat Clear Sealer

Product Codes:

432-1220

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit stearated paper prior to staining or coating. Sealers should be sanded with 240, 280 and 320 grit stearated paper prior to being coated. Stain systems used under acid catalyzed systems should be acid stable. AkzoNobel recommends 825-90XX, 825-91XX Promatch® C-Mix Stains, or 890-85XX Promatch Dye Stains. Danseal cannot be used on metal, old oil or cellulose lacquers.

General Information:

Agitate material thoroughly before use. Always mix Danseal while adding catalyst in the recommended mixing ratios. Apply and allow to dry for one hour. Scuff sand with 220 to 280 grit stearated paper before topcoating to ensure good adhesion and a smooth finish. The second and subsequent coats must be applied the same day as the previous coat is sanded.

Danseal must not be used and dried at temperatures below 64°F or relative humidity above 65%. During the curing process, the coating must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finished surface. This may accelerate discoloration.

Maximum film build of Danseal should not exceed 2 mils dry. Maximum film build of total coating system must not exceed 4 mils dry.

Contact with metal surfaces should be avoided.

PDF Name: US-PIS_432-1220_Danseal_Post-Cat_Clear_Sealer

Tack Free Time: 15 – 20 minutes

Files: US-PIS_432-1220_Danseal_Post-Cat_Clear_Sealer.pdf

Dry to Sand : 1 hour

Dry to Stack: 8 hours

Tack Free Time: Flash off before entering oven

VOC less exempt lb/gal: <5.20

Dry to Sand: 20 – 30 minutes

VOC lb/gal: <4.47

VOC less exempt g/l: <625

VOC g/l: <540

VOC lb/lb Solid: <1.85

Dry to Stack: 40 – 45 minutes

VHAPs lb/lb Solid: <0.7

Note: N/A

Note:

N/A

spec_description:

Danseal is a high solids modified Reactive Amino Coating (RAC). Danseal provides good clarity, fast dry and excellent sanding characteristics.

spec_uses:

Danseal is specifically made for use under Danspeed 424-45XX, Danspeed Elite 424-44XX, Plastofix Light 421-48XX and E-Var 421-80XX.

Suggested Uses:

Wood Sealer

Mixing Ratio:

100 parts 432-1220 to 7 parts 873-0870

Pot Life:

12 hours

Application Viscosity:

Zahn #2 signature cup 20 – 24 seconds

Reducer: 803-1325

Retarder: 800-5328

Clean-up Solvent: 803-1298

Recommended Wet Film: 3 – 5 mils

Coverage:

385 sq. ft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 24 sec at 77°F

Flash Point: 24°F (-4°C)

Density (lb/gal): 7.8

Solid (% by weight): 31%

Solid (% by volume): 23%

Shelf Life (months): 12

DANSEAL Sealer

432-1220 Danseal Post-Cat Clear Sealer

Find distributor Trouver un distributeur

spec_description:

Danseal is a high solids modified Reactive Amino Coating (RAC). Danseal provides good clarity, fast dry and excellent sanding characteristics.

BACK

DANSEAL Sealer

432-1220 Danseal Post-Cat Clear Sealer

spec_description:

Danseal is a high solids modified Reactive Amino Coating (RAC). Danseal provides good clarity, fast dry and excellent sanding characteristics.

Product codeCodes de produit
Product Codes:

432-1220

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 24 sec at 77°F

Flash Point: 24°F (-4°C)

Density (lb/gal): 7.8

Solid (% by weight): 31%

Solid (% by volume): 23%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_432-1220_Danseal_Post-Cat_Clear_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap