CHEMVINYL Sealer

546-8002 Chemvinyl Clear Vinyl Sealer

Product Codes:

546-8002

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit stearated paper prior to staining or coating. Stain system used under acid catalyzed systems should be acid stable. AkzoNobel recommends using 825-90XX C-Mix stains or 890-85XX N.G.R. stains.

General Information:

Apply at 3 – 5 wet mils on sanded substrate. Maximum film build of Chemvinyl is not to exceed 2 mil dry. Allow 45 minutes to one hour to dry at a minimum of 68°F (20°C) prior to topcoating.

Sand with 280/320 grit paper before topcoating and ensure topcoat is applied the same day the sanding is done.

Always mix Chemvinyl while adding reducers in the recommended mixing ratios. Chemvinyl must be thoroughly agitated at all times to ensure product consistency.

Chemvinyl is used for sealing wooden furniture and other wood surfaces for interior use only. It can be used on all wood types and after drying and sanding, may be overcoated with acid curing systems such as Danspeed (432-XXXX, 424-XXXX), Plastofix (421-XXXX). Chemvinyl may also be overcoated with pre-catalyzed materials such as Opticlear 431-8XXX or Chemcab 431-6XXX.

PDF Name: US-PIS_546-8002_Chemvinyl_Clear_Vinyl_Sealer

Tack Free Time: 10 – 15 minutes

Files: US-PIS_546-8002_Chemvinyl_Clear_Vinyl_Sealer.pdf

Dry to Sand : 30 minutes

Dry to Stack: 45 minutes

Tack Free Time: Flash off before entering oven

VOC less exempt lb/gal: <5.45

Dry to Sand: 15 – 20 minutes

VOC lb/gal: <2.65

VOC less exempt g/l: <650

VOC g/l: <320

VOC lb/lb Solid: <1.9

Dry to Stack: 30 minutes

VHAPs lb/lb Solid: <0.002

Note: N/A

Note:

N/A

spec_description:

Chemvinyl is a ready to use vinyl sanding sealer with good clarity and moisture resistance. It is a quick drying product with excellent sanding properties and is to be used where excellent adhesion is important. Chemvinyl provides a very good moisture barrier. It provides excellent adhesion to most wood species, as well as to topcoats.

spec_uses:

This product is recommended for sealing kitchen cabinets, vanities as well as many other interior wood applications where adhesion or moisture may be a concern.

Suggested Uses:

Wood Sealer

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 15 – 18 seconds

Reducer: 803-1325

Retarder: 800-5328

Clean-up Solvent: 803-1298

Recommended Wet Film: 3 – 5 mils

Coverage:

200 sq ft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 30 sec at 77°F

Flash Point: -4°F (-20°C)

Density (lb/gal): 7.4

Solid (% by weight): 18%

Solid (% by volume): 12%

Shelf Life (months): 12

CHEMVINYL Sealer

546-8002 Chemvinyl Clear Vinyl Sealer

Find distributor Trouver un distributeur

spec_description:

BACK

CHEMVINYL Sealer

546-8002 Chemvinyl Clear Vinyl Sealer

spec_description:

Product codeCodes de produit
Product Codes:

546-8002

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 30 sec at 77°F

Flash Point: -4°F (-20°C)

Density (lb/gal): 7.4

Solid (% by weight): 18%

Solid (% by volume): 12%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_546-8002_Chemvinyl_Clear_Vinyl_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap