CHEMLACK Topcoat

441-51XX Chemlack 275 NC Clear TC

Product Codes:

441-5110 Matte
441-5120 Low Gloss
441-5140 Satin
441-5160 Semi-Gloss
441-5190 High Gloss

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit stearated paper prior to staining or coating. Sealers should be sanded with 240, 280 and 320 grit stearated papers prior to being coated. Appropriate sealers are Chemcraft lacquer sealers or self-seal. Appropriate stains are 825-39XX series stains or 824-50XX series waterborne stains.

General Information:

Agitate material before use. Chemlack 275 must be agitated thoroughly at all times to ensure product consistency. Apply 3-5 wet mils on sanded substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper.

Maximum film build of Chemlack 275 should not exceed 3 mils dry. Maximum film build of total coating system must not exceed 3 mils dry.

PDF Name: US-PIS_441-51XX_Chemlack_275_NC_Clear_TC

Tack Free Time: 10 minutes

Files: US-PIS_441-51XX_Chemlack_275_NC_Clear_TC.pdf

Dry to Sand : 20 - 25 minutes

Dry to Stack: 2 - 3 hours

Tack Free Time: Flash off before entering oven

VOC less exempt lb/gal: <2.29

Dry to Sand: 15 – 20 minutes

VOC lb/gal: <0.60

VOC less exempt g/l: <275

VOC g/l: <72

VOC lb/lb Solid: <0.35

Dry to Stack: 60 – 90 minutes

VHAPs lb/lb Solid: <0.001

Note: N/A

Note:

N/A

spec_description:

Chemlack 275 is a single component nitrocellulose lacquer that provides good depth and clarity. This product has been formulated to meet 275 g/L VOC regulations.

spec_uses:

Chemlack 275 is recommended for household furniture, millwork, decorative items as well as many other interior wood applications

Suggested Uses:

Wood Finish

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 18 – 22 seconds

Reducer: 803-1325 or 803-1349

Retarder: 800-5915

Clean-up Solvent: 800-5500

Recommended Wet Film: 3 – 5 mils

Coverage:

270 sq. ft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

The addition of these reducers or retarders could affect 275 VOC compliance.

Viscosity:

Zahn #2 signature cup 22 sec at 77°F

Flash Point: 0°F (-18°C)

Density (lb/gal): 7.58

Solid (% by weight): 23%

Solid (% by volume): 17%

Shelf Life (months): 12

CHEMLACK Topcoat

441-51XX Chemlack 275 NC Clear TC

Find distributor Trouver un distributeur

spec_description:

Chemlack 275 is a single component nitrocellulose lacquer that provides good depth and clarity. This product has been formulated to meet 275 g/L VOC regulations.

BACK

CHEMLACK Topcoat

441-51XX Chemlack 275 NC Clear TC

spec_description:

Chemlack 275 is a single component nitrocellulose lacquer that provides good depth and clarity. This product has been formulated to meet 275 g/L VOC regulations.

Product codeCodes de produit
Product Codes:

441-5110 Matte
441-5120 Low Gloss
441-5140 Satin
441-5160 Semi-Gloss
441-5190 High Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 22 sec at 77°F

Flash Point: 0°F (-18°C)

Density (lb/gal): 7.58

Solid (% by weight): 23%

Solid (% by volume): 17%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_441-51XX_Chemlack_275_NC_Clear_TC.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap