AQUALUX II Topcoat
423-29XX Aqualux® 275 WB Clear TC
Product Codes:
423-2910 Matte
423-2940 Satin
Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit stearated paper prior to staining or coating. The surface being prepared must be clean and dry before the coating is applied. Sealers, if used, should be sanded prior to being coated with 280/320 grit stearated paper. Appropriate sealers are Aqualux Sealer 423-2900, or self seal. Aqualux 275 cannot be used on metal, old oil or cellulose lacquers. AkzoNobel recommends using 825-39XX stains.
General Information:
Agitate material before use. Aqualux 275 must be agitated thoroughly at all times to ensure product consistency and consistent gloss. Avoid high speed agitation to minimize entrapment of air.

Apply at 2-4 mils wet on sanded substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper.

Maximum film build of Aqualux 275 should not exceed 4 mils dry. Maximum film build of total coating system must not exceed 4 mils dry. Contact with metal surfaces should be avoided.

Aqualux 275 must not be used and dried at temperatures below 64°F or relative humidity above 65%.
PDF Name: US-PIS_423-29XX_Aqualux®_275_WB_Clear_TC
Tack Free Time: 15 – 20 minutes
Files: US-PIS_423-29XX_Aqualux®_275_WB_Clear_TC.pdf
Dry to Sand : 30 - 40 minutes
Dry to Stack: Overnight
Tack Free Time: 10 – 15 minutes
VOC less exempt lb/gal: <1.71
Dry to Sand: 20 – 30 minutes
VOC lb/gal: <0.43
VOC less exempt g/l: <205
VOC g/l: <52
VOC lb/lb Solid: <0.18
Dry to Stack: 4 – 6 hours
VHAPs lb/lb Solid: <.01
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Aqualux 275 is a high quality waterborne coating. Aqualux applies easily and typically shows much improved transfer efficiency over solvent borne finishes. Aqualux 275 is a fast drying, good building product that shows excellent resistance to both chemicals and to physical wear. The coating has excellent leveling, a smooth even appearance and low grain raising.

Aqualux 275 is supplied at a ready to spray viscosity. This coating will dry quickly, sand easily and can be used a self seal finish.

Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards.

Recommended: Architectural Woodwork Institute Water Acrylic System (8^th Ed).
spec_uses:
Aqualux 275 is recommended for household furniture, millwork and fixtures as well as many other interior wood applications. Aqualux 275 is a light stable finish designed for use on all types of solid wood and veneer meant for interior use.
Suggested Uses:
Wood Finish
Mixing Ratio:
N/A
Pot Life:
N/A
Application Viscosity:
Zahn #2 signature cup 40 seconds
Reducer: N/A
Retarder: N/A
Clean-up Solvent: Wet – 80:20 blend water and 800-5742, Dried – 800-5500
Recommended Wet Film: 2 – 4 mils
Coverage:
Coverage is 450 sq. ft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #2 signature cup 40 sec at 77°F
Flash Point: >140°F
Density (lb/gal): 8.6
Solid (% by weight): 34%
Solid (% by volume): 31%
Shelf Life (months): 12

AQUALUX II Topcoat

423-29XX Aqualux® 275 WB Clear TC

Find distributor Trouver un distributeur

spec_description:

Aqualux 275 is a high quality waterborne coating. Aqualux applies easily and typically shows much improved transfer efficiency over solvent borne finishes. Aqualux 275 is a fast drying, good building product that shows excellent resistance to both chemicals and to physical wear. The coating has excellent leveling, a smooth even appearance and low grain raising.

Aqualux 275 is supplied at a ready to spray viscosity. This coating will dry quickly, sand easily and can be used a self seal finish.

Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards.

Recommended: Architectural Woodwork Institute Water Acrylic System (8^th Ed).

BACKRetour

Product codeCodes de produit
Product Codes:

423-2910 Matte
423-2940 Satin

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 40 sec at 77°F
Flash Point: >140°F
Density (lb/gal): 8.6
Solid (% by weight): 34%
Solid (% by volume): 31%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_423-29XX_Aqualux®_275_WB_Clear_TC.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more