AQUALUX UNICLEAR Sealer

423-2900 Aqualux® 275/550 WB Clear Sealer

Product Codes:

423-2900

Surface Preparation:

Substrate should be sanded using 120, 150 or 180 grit sandpaper prior to staining or coating. Stain systems recommended under this product are Promatch® Aqua Wiping Stains 824-50XX or 824-51XX and Promatch C-Mix 250 VOC Stains 825-39XX.

General Information:

Mix material before use. Add water to reduce, if required, and mix thoroughly. Apply by spray at wet film builds of 4-5 mils. Application and drying conditions must be at temperatures of 64°F or above and at a humidity of less than 65%. Increased airflow and/or drying temperatures, including the use of infrared, will greatly decrease dry times.

Apply at 4-5 mils wet on sanded substrate.

Aqualux Sealer must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces should be avoided.

Film build should not exceed 2 dry mils per coat. Total film build must not exceed 4 dry mils.

Aqualux Sealer must not be polluted with oil, solvent based paint or the like and should not be applied to metal surfaces. Aqualux Sealer must not be sanded with steel wool. This coating must not be used and dried at temperatures below 64°F or relative humidity above 65%.

PDF Name: US-PIS_423-2900_Aqualux_275-550_WB_Clear_Sealer

Tack Free Time: 15 – 20 minutes

Files: US-PIS_423-2900_Aqualux_275-550_WB_Clear_Sealer.pdf

Dry to Sand : 1 hour

Dry to Stack: 8 hours

Tack Free Time: 10 – 15 minutes

VOC less exempt lb/gal: <1.40

Dry to Sand: 45 minutes

VOC lb/gal: <0.50

VOC less exempt g/l: <163

VOC g/l: <60

VOC lb/lb Solid: <0.17

Dry to Stack: 6 hours

VHAPs lb/lb Solid: <0.003

Note: N/A

Note:

N/A

spec_description:

Aqualux Sealer is a fast drying sealer with very good sanding properties. In the curing cycle, the addition of heat and air movement will shorten the drying time.

spec_uses:

Aqualux Sealer is waterborne acrylic sealer designed for interior furniture, fittings, kitchen cabinet and other wood applications.

Suggested Uses:

Wood Sealer

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 43 seconds

Reducer: Water

Retarder: N/A

Clean-up Solvent: Water or 80/20 blend water/800-5742

Recommended Wet Film: 4 – 5 mils

Coverage:

Coverage is 486 sq. ft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 50 sec at 77° F

Flash Point: >200°F

Density (lb/gal): 8.7

Solid (% by weight): 32%

Solid (% by volume): 28%

Shelf Life (months): 12

AQUALUX UNICLEAR Sealer

423-2900 Aqualux® 275/550 WB Clear Sealer

Find distributor Trouver un distributeur

spec_description:

Aqualux Sealer is a fast drying sealer with very good sanding properties. In the curing cycle, the addition of heat and air movement will shorten the drying time.

BACK

AQUALUX UNICLEAR Sealer

423-2900 Aqualux® 275/550 WB Clear Sealer

spec_description:

Aqualux Sealer is a fast drying sealer with very good sanding properties. In the curing cycle, the addition of heat and air movement will shorten the drying time.

Product codeCodes de produit
Product Codes:

423-2900

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 50 sec at 77° F

Flash Point: >200°F

Density (lb/gal): 8.7

Solid (% by weight): 32%

Solid (% by volume): 28%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_423-2900_Aqualux_275-550_WB_Clear_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap