C-MIX Intermix System

825-3901 Promatch® C-Mix 275 Wiping SB Stain

Product Codes:

825-3901 Natural

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit stearated paper prior to staining Sealers, if used, should be sanded prior to being coated with 280/320 grit stearated paper. Appropriate sealers are Chemcraft 275 sealers.

General Information:

Agitate material before use. Promatch C-Mix 275 Stains must be agitated thoroughly at all times to ensure product consistency and consistent gloss.

Application by spray. These stains must then be wiped into the grain and wiped clean with a clean rag to ensure good adhesion by subsequent clear coats.

PDF Name: US-PIS_825-3901_Promatch_C-Mix_275_Wiping_SB_Stain

Tack Free Time: 1 hour

Files: US-PIS_825-3901_Promatch_C-Mix_275_Wiping_SB_Stain.pdf

Dry to Sand : N/A

Dry to Stack: N/A

Tack Free Time: 30 – 40 minutes

VOC less exempt lb/gal: <3.4

Dry to Sand: N/A

VOC lb/gal: <2.08

VOC less exempt g/l: <408

VOC g/l: <250

VOC lb/lb Solid: <0.40

Dry to Stack: N/A

VHAPs lb/lb Solid: <0.10

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

Promatch C-Mix 275 Stains 825-39XX offer a simple, low VOC one step stain color with good clarity and ease of workability. They may be clear coated with any of the Chemcraft solvent based Chemlack 275, Opticlear 275 or Plastofix Light 275 products as well as the sealers associated with these systems.

All Promatch C-Mix 275 stains are acid stable. They will not change color when an acid cured Chemcraft product is used to seal and topcoat them.

spec_uses:

Promatch C-Mix 275 Stains 825-39XX are all-purpose wipe stains for furniture, millwork and cabinets.

Suggested Uses:

Wood Stain

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

N/A

Reducer: N/A

Retarder: N/A

Clean-up Solvent: 800-5500

Recommended Wet Film: N/A

Coverage:

Coverage will vary depending on method of application and required color depth.

Note application:

N/A

Viscosity:

N/A at 77°F

Flash Point: -4°F (-20°C)

Density (lb/gal): 7.1 – 8.3

Solid (% by weight): 33 – 56%

Solid (% by volume): 29 – 52%

Shelf Life (months): 24

C-MIX Intermix System

825-3901 Promatch® C-Mix 275 Wiping SB Stain

Find distributor Trouver un distributeur

spec_description:

All Promatch C-Mix 275 stains are acid stable. They will not change color when an acid cured Chemcraft product is used to seal and topcoat them.

BACK

C-MIX Intermix System

825-3901 Promatch® C-Mix 275 Wiping SB Stain

spec_description:

All Promatch C-Mix 275 stains are acid stable. They will not change color when an acid cured Chemcraft product is used to seal and topcoat them.

Product codeCodes de produit
Product Codes:

825-3901 Natural

Product information

Product specificationsSpécifications du produit

Viscosity:

N/A at 77°F

Flash Point: -4°F (-20°C)

Density (lb/gal): 7.1 – 8.3

Solid (% by weight): 33 – 56%

Solid (% by volume): 29 – 52%

Shelf Life (months): 24

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_825-3901_Promatch_C-Mix_275_Wiping_SB_Stain.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap