- Isolante
- 420-1205 Isolante Sealer Neutre
- Product Codes:
420-1205
- Surface Preparation:
Wood must be sanded with a 120 or 150 grit paper and free of dust and all contaminants. Plastic substrates should be scuffed with Scotch Brite to improve adhesion. Substrates that cannot be sanded should be wiped clean and degreased if possible.
- General Information:
Mix product with hardener. Apply 2 to 4 wet mils on a sanded surface. Let dry for 30 to 60 minutes and apply the desired topcoat. If the drying time exceeds 4 hours, sanding is required to keep a good adhesion. This product can be tinted with 844 tints and dyes. Once catalyzed with 876-9084, this product will contain isocyanates. Take necessary precautions for the handling and use of this product. See MSDS. Total dry film build of Isolante should not exceed 1 dry mil. The total system build will be dependent upon the topcoat applied.
For a complete system cure, the system must be applied at a temperature above 18ºC and relative humidity below 65%.
Complete system must be verified and approved by AkzoNobel before going on production.
Isolante is recommended with the following topcoat: 458-1260, 436-1399. Others may be recommended as well, speak with your technical sales representative.
- PDF Name: CA-PIS_420-1205_Isolante_Sealer_Neutre
- Tack Free Time: 30 - 60 minutes
- Files: CA-PIS_420-1205_Isolante_Sealer_Neutre.pdf
- Dry to Sand : 4 hours
- Dry to Stack: 8 hours
- Tack Free Time: 5 - 10 minutes
- test: 20 – 30 minutes
- VOC less exempt g/l: 700
- VOC g/l: 700
- Dry to Stack: 4 hours
- Note:
See individual compliance sheets for specific data
- spec_description:
Isolante is a two component ‘tie-coat’ polyurethane type sealer that is designed to improve the adhesion between topcoats and substrates where poor adhesion would otherwise be obtained. These would include a wide variety of plastics, stained or exotic woods.
- spec_uses:
Isolante is normally used as a washcoat applied directly to the substrate in order to ensure good adhesion and oil blocking properties. It is suitable for all types of wood, MDF, veneers and some type of plastic.
- Suggested Uses:
Spray
- Mixing Ratio:
2:1 with 876-9084
- Pot Life: 3 hours
- Application Viscosity:
22 ± 2 sec Zahn #2 at 25°C
- Reducer: 800-5301 or 121-834 if needed
- Retarder: 800-5328 EEP
- Clean-up Solvent: Lacquer Thinner (do not mix with product)
- Recommended Wet Film: 2 to 4 mils wet
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
Zahn #4 signature cup 28 sec at 25°C
- Flash Point: -6°C
- Density (lb/gal): 0.92 ± 2% at 25°C
- Solid (% by weight): 24 ± 2%
- Solid (% by volume): 16 ± 2%
- Shelf Life (months): 12
- Lustrate
- 634-794 Lustrate White PU Pigmented Topcoat
- Product Codes:
634-794 High Gloss
- Surface Preparation:
Primer should be well sanded using 240, 320 and 360 grit stearated paper. Suitable primers are polyurethane (283-XXX) or polyester (740-XXX) types. Care should be taken during sanding to avoid sanding through the primer.
- General Information:
Mix the desired amount of material and apply 4-6 mils wet. The high gloss coating, when cured, is very suitable to be buffed and polished where dust free conditions are not available.
The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the mixed material should be monitored regularly to maintain a consistent appearance.
The mixed product contains 876-9081, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials.
Total recommended film thickness of Lustrate is not to exceed 6 mils dry.Primers to use under 634-794: polyurethane 283-3XX or polyester 740-XXX.
- PDF Name: CA-PIS_634-794_Lustrate_White_PU_Pigmented_Topcoat
- Tack Free Time: 15 - 30 minutes
- Files: CA-PIS_634-794_Lustrate_White_PU_Pigmented_Topcoat.pdf
- Dry to Sand : Overnight
- Dry to Stack: Overnight
- Tack Free Time: Flash off before entering oven
- test: 3 hours
- VOC less exempt g/l: 407
- VOC g/l: 407
- Dry to Stack: 4 hours
- Note:
See individual compliance sheets for specific data
- spec_description:
Lustrate White is a two component polyurethane enamel with a tough cross linked film. The coating is very resistant to scratching and household chemicals when cured, and can provide exceptional gloss.
- spec_uses:
Lustrate is used whenever premium performance characteristics are required for interior wood finishing.
- Suggested Uses: Spray
- Mixing Ratio:
1:1 with 876-9081
- Pot Life:
3 hours
- Application Viscosity:
Zahn #2 signature cup 20-25 seconds
- Reducer: 121-834 or 800-5301
- Retarder: 800-5328 EEP
- Clean-up Solvent: Lacquer Thinner (do not mix with product)
- Recommended Wet Film: 4-6 wet mils
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
Zahn #3 signature cup 35 sec at 25°C
- Flash Point: 27°C (80°F)
- Density (lb/gal): 1.36
- Solid (% by weight): 69%
- Solid (% by volume): 55%
- Shelf Life (months): 12
- Lustrate
- 436-2104 Lustrate PU Clear Sealer
- Product Codes:
436-2104
- Surface Preparation:
Substrate should be sanded with 120, 150 or 180 grit sandpaper prior to finishing. Difficult or oily substrates may require the use of 401-033 Isolante Sealer prior to priming to ensure maximum adhesion.
- General Information:
Prepare material as per hardener mixing ratio and apply over desired surface at 3-5 mils wet.
Mixed product will contain 999-067, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials. The relative humidity in the application and drying rooms should never exceed 75%.
After drying, scuff sand with 280-320 grit paper and topcoat within eight hours. If left over eight hours, the sealer should be re-sanded prior to topcoating.
Total dry film build of the system including topcoat is not to exceed 6 dry mils.Topcoats to use over 436-2104: Chemlite 436-31XX or Lustrate 436-1399.
- PDF Name: CA-PIS_436-2104_Lustrate_PU_Clear_Sealer
- Tack Free Time: 10 - 15 minutes
- Files: CA-PIS_436-2104_Lustrate_PU_Clear_Sealer.pdf
- Dry to Sand : 20 - 30 minutes
- Dry to Stack: Overnight
- Tack Free Time: 3 - 5 minutes
- test: 10 - 15 minutes
- VOC less exempt g/l: 692
- VOC g/l: 692
- Dry to Stack: 2 - 4 hours
- Note:
See individual compliance sheets for specific data
- spec_description:
Lustrate Sealer is designed to provide the improved adhesion characteristics typical of a urethane material. When topcoated with Chemlite or Lustrate, the system provides exceptional durability and light stability.
- spec_uses:
436-2104 is suitable for sealing all types of wood and wood veneers for interior use. The product provides very good water resistance and offers protection from tannin bleed.
- Suggested Uses: Spray
- Mixing Ratio:
10:1 (10%) with 999-067 (other hardeners possible)
- Pot Life:
2-3 hours
- Application Viscosity:
Zahn #2 signature cup 20-25 seconds
- Reducer: 100-120, 800-5301 or 121-834
- Retarder: 800-5328 EEP
- Clean-up Solvent: Lacquer Thinner (do not mix with product)
- Recommended Wet Film: 3-5 wet mils
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
Zahn #2 signature cup 20 sec at 25°C
- Flash Point: -1°C (30°F)
- Density (lb/gal): 0.94
- Solid (% by weight): 27%
- Solid (% by volume): 21%
- Shelf Life (months): 12
- D-Dur
- 620-1XX D-Dur PU Clear Topcoat
- Product Codes:
620-117 Low Gloss
620-106 Satin
620-114 Gloss - Surface Preparation:
Wood substrate should be sanded with 120, 150 or 180 grit prior to staining or coating. Primer should be well sanded using 240, 280 or 320 grit stearated paper.
- General Information:
Mix the desired amount of material and apply 3-5 mils wet.
The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the mixed material should be monitored regularly to maintain a consistent appearance.
Mixed product will contain 999-062, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials.
Total recommended film thickness of D-Dur system is not to exceed 6 mils dry.This product should be used as a self-seal.
- PDF Name: CA-PIS_620-1XX_D-Dur_PU_Clear_Topcoat
- Tack Free Time: 20 - 30 minutes
- Files: CA-PIS_620-1XX_D-Dur_PU_Clear_Topcoat.pdf
- Dry to Sand : 6 - 8 hours
- Dry to Stack: Overnight
- Tack Free Time: 15 - 20 minutes
- test: 2 - 3 hours
- VOC less exempt g/l: 654
- VOC g/l: 654
- Dry to Stack: Overnight
- Note:
See individual compliance sheets for specific data
- spec_description:
D-Dur is a two-component polyurethane with very good wetting properties. It provides excellent flexibility and good resistance to weathering.
- spec_uses:
This finish is recommended for wooden surfaces where good outdoor durability is desired (i.e., window frames, doors, wooden garden furniture).
- Suggested Uses: Spray
- Mixing Ratio:
4:1 with 999-062
- Pot Life:
3 hours
- Application Viscosity:
Zahn #2 signature cup 20-25 seconds
- Reducer: 121-834 or 800-5301
- Retarder: 800-5328 EEP
- Clean-up Solvent: Lacquer Thinner (do not mix with product)
- Recommended Wet Film: 3-5 wet mils
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
Zahn #2 signature cup 22 sec at 25°C
- Flash Point: 15°C (59°F)
- Density (lb/gal): 0.97
- Solid (% by weight): 33%
- Solid (% by volume): 26%
- Shelf Life (months): 12
- Lustrate
- 436-1399 Lustrate PU Clear Topcoat
- Product Codes:
436-1399 High Gloss
- Surface Preparation:
Primer should be well sanded using 240, 320 and 360 grit stearated paper. Care should be taken during sanding to avoid sanding through the primer. The clear system sealer is 436-2104.
- General Information:
Mix the desired amount of material and apply 4-6 mils wet. The coating when cured is very suitable to be buffed and polished where dust free conditions are not available.
The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the mixed material should be monitored regularly to maintain a consistent appearance.
The mixed product contains 876-9081, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials.
Total recommended film thickness of Lustrate is not to exceed 6 mils dry.Sealers to use under 436-1399: polyurethane 436-2104 or 283-3XX or polyester (740-XXX).
- PDF Name: CA-PIS_436-1399_Lustrate_PU_Clear_Topcoat
- Tack Free Time: 15 - 30 minutes
- Files: CA-PIS_436-1399_Lustrate_PU_Clear_Topcoat.pdf
- Dry to Sand : Overnight
- Dry to Stack: Overnight
- Tack Free Time: Flash off before entering oven
- test: 3 hours
- VOC less exempt g/l: 450
- VOC g/l: 450
- Dry to Stack: 4 hours
- Note:
See individual compliance sheets for specific data
- spec_description:
Lustrate is a two component polyurethane enamel with a tough cross linked film. The coating is very resistant to scratching and household chemicals when cured, and can provide exceptional gloss and clarity.
- spec_uses:
Lustrate is used whenever premium performance characteristics are required for interior wood finishing.
- Suggested Uses: Spray
- Mixing Ratio:
1:1 with 876-9081
- Pot Life:
3 hours
- Application Viscosity:
Zahn #2 signature cup 20-25 seconds
- Reducer: 121-834 or 800-5301
- Retarder: 800-5328 EEP
- Clean-up Solvent: Lacquer Thinner (do not mix with product)
- Recommended Wet Film: 4-6 wet mils
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
Zahn #2 signature cup 45 sec at 25°C
- Flash Point: 24°C (75°F)
- Density (lb/gal): 1.03
- Solid (% by weight): 56%
- Solid (% by volume): 50%
- Shelf Life (months): 12
Need help? Contact our team of wood coating experts.
