Acryllak
423-95XX Acryllak WB Clear Topcoat
Product Codes:

423-9520 20° Low Gloss
423-9535 35° Satin
423-9550 50° Semi-Gloss
423-9590 90° High Gloss

Surface Preparation:

Substrate to be coated should be sanded with 150 or 180 grit sandpaper prior to coating. This product may be used self-sealed or sealed with 423-10XX line Aqualux.

General Information:

Mix material before use. Apply by spray at wet film builds of 3-5 mils. Application and drying conditions must be at temperatures of 18°C or higher and at a humidity of less than 65%. Increased air flow or drying temperatures, including the use of infrared, will greatly decrease dry times.
Further coats may be applied after complete drying followed by sanding with 280/320 grit sandpaper. Second and subsequent coats must be applied the same day as the board is sanded.
Product must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces should be avoided.
Film build should not exceed 2 dry mils per coat. Total film build must not exceed 4 dry mils.

PDF Name: CA-PIS_423-95XX_Acryllak_WB_Clear_Topcoat
Tack Free Time: 20 minutes
Files: CA-PIS_423-95XX_Acryllak_WB_Clear_Topcoat.pdf
Dry to Sand : 2 - 3 hours
Dry to Stack: 12 hours
Tack Free Time: Flash off before entering oven
Dry to Sand: 45 minutes
VOC less exempt g/l: 243
VOC g/l: 110
Dry to Stack: 8 hours
Note: N/A
Note:

See individual compliance sheets for specific data

spec_description:

Acryllak is an acrylic modified polyurethane waterborne clear finish. Acryllak is a wear resistant, fast drying and environmentally clean lacquer. It is resistant to conventional detergents and household cleaners.

spec_uses:

For interior use for wood furniture and kitchen cabinetry

Suggested Uses:

Clear Waterborne Lacquer

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 58 seconds

Reducer: Water if necessary
Retarder: N/A
Clean-up Solvent: Soap and water when wet, 4:1 water:800-5742 if dried
Recommended Wet Film: 3-5 mils wet
Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #2 signature cup 58 sec at 25°C

Flash Point: >93°C (200F)
Density (lb/gal): 1.03
Solid (% by weight): 36 ± 1%
Solid (% by volume): 33 ± 1%
Shelf Life (months): 12

Acryllak

423-95XX Acryllak WB Clear Topcoat

Find distributor Trouver un distributeur

spec_description:

Acryllak is an acrylic modified polyurethane waterborne clear finish. Acryllak is a wear resistant, fast drying and environmentally clean lacquer. It is resistant to conventional detergents and household cleaners.

Read more

Acryllak

423-95XX Acryllak WB Clear Topcoat

spec_description:

Acryllak is an acrylic modified polyurethane waterborne clear finish. Acryllak is a wear resistant, fast drying and environmentally clean lacquer. It is resistant to conventional detergents and household cleaners.

Read more
Product codeCodes de produit
Product Codes:

423-9520 20° Low Gloss
423-9535 35° Satin
423-9550 50° Semi-Gloss
423-9590 90° High Gloss


Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 58 sec at 25°C

Flash Point: >93°C (200F)
Density (lb/gal): 1.03
Solid (% by weight): 36 ± 1%
Solid (% by volume): 33 ± 1%
Shelf Life (months): 12

Download product information sheets

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Image

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Need help? Contact our team of wood coating experts.

Contact us