Isolante
401-0330 Isolante PU Clear Sealer
Product Codes:
410-0330
Surface Preparation:
Wood must be sanded with a 120, 150 or 180 grit paper and free of dust and all contaminants. Plastic substrates should be scuffed with Scotch Brite to improve adhesion. Substrates that cannot be sanded should be wiped clean and degreased if possible.
General Information:
Mix product with hardener and reducer to the recommended viscosity. Apply 2 to 4 wet mils on a sanded surface. Let dry for 30 to 60 minutes and apply the desired topcoat. If the drying time exceeds 4 hours, sanding is required to keep a good adhesion. Once catalyzed with 999-0660, this product will contain isocyanates. Take necessary precautions for the handling and use of this product. See MSDS. Total dry film build of Isolante should not exceed 1 dry mil. The total system build will be dependent upon the topcoat applied.
For a complete system cure, the system must be applied at a temperature above 18ºC and relative humidity below 65%.
Complete system must be verified and approved by AkzoNobel before going on production.
Suitable topcoats include Lustrate, Chemlite, Reslack and Plasticolor. Others may be recommended as well, speak with your technical sales representative.
PDF Name: CA-PIS_401-0330_Isolante_PU_Clear_Sealer
Tack Free Time: 30 - 60 minutes
Files: CA-PIS_401-0330_Isolante_PU_Clear_Sealer.pdf
Dry to Sand : 4 hours
Dry to Stack: 8 hours
Tack Free Time: 5 - 10 minutes
Dry to Sand: 20 - 30 minutes
VOC less exempt g/l: 651
VOC g/l: 651
Dry to Stack: 4 hours
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Isolante Sealer is a two component ‘tie-coat’ polyurethane type sealer that is designed to improve the adhesion between topcoats and substrates where poor adhesion would otherwise be obtained. These would include a wide variety of plastics, stained or exotic woods.
spec_uses:
Isolante Sealer is normally used as a washcoat applied directly to the substrate in order to ensure good adhesion and oil blocking properties. It is suitable for all types of wood, MDF, veneers and some type of plastic.
Suggested Uses:
Spray
Mixing Ratio:
2:1 with 876-9066 or 999-0660
Pot Life: 2-3 hours
Application Viscosity:
20-25 sec Zahn #2 at 25°C
Reducer: 800-5301 or 121-834
Retarder: 800-5328 EEP
Clean-up Solvent: Lacquer Thinner (do not mix with product)
Recommended Wet Film: 2-4 mils wet
Coverage:
N/A
Note application:
N/A
Viscosity:
Zahn #4 signature cup 24 sec at 25°C
Flash Point: -6°C
Density (lb/gal): 0.94 ± 2% at 25°C
Solid (% by weight): 31 ± 2%
Solid (% by volume): 21 ± 2%
Shelf Life (months): 12

Isolante

401-0330 Isolante PU Clear Sealer

Find distributor Trouver un distributeur

spec_description:

Isolante Sealer is a two component ‘tie-coat’ polyurethane type sealer that is designed to improve the adhesion between topcoats and substrates where poor adhesion would otherwise be obtained. These would include a wide variety of plastics, stained or exotic woods.

BACKRetour

Product codeCodes de produit
Product Codes:

410-0330

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #4 signature cup 24 sec at 25°C
Flash Point: -6°C
Density (lb/gal): 0.94 ± 2% at 25°C
Solid (% by weight): 31 ± 2%
Solid (% by volume): 21 ± 2%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_401-0330_Isolante_PU_Clear_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more