Catlac
131-50XX Catlac White Pre-Cat Pigmented Topcoat
Product Codes:
131-5015 15° Low Gloss
131-5020 20° Low Gloss
131-5035 35° Satin
131-5050 50° Semi-Gloss
Surface Preparation:
Before application of Catlac White, the basecoat must be sanded using 280/320 grit paper and free of dust and all contaminants. This product must not be applied over metal, old finish or nitrocellulose lacquer.
General Information:
Keep under mixing to assure consistency of the product. Apply 3 to 5 wet mils on sanded surface. One extra coat can be applied following a complete cure and a sanding with a 280/320 paper. Avoid all contact with metallic surfaces. Maximum film build of the topcoat should not exceed 2 mils dry. Maximum film build of the system should not exceed 4 mils dry.
To obtain complete cure, system should be applied at a temperature above 18°C and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surfaces must not be cleaned with ammonia containing products. Always use plastic or stainless equipment to eliminate discoloration due to oxidation.
Basecoats to use with 131-50XX: 225-0010, 522-1624, 545-8016, 546-7257
PDF Name: CA-PIS_131-50XX_Catlac_White_Pre-Cat_Pigmented_Topcoat
Tack Free Time: 15 - 20 minutes
Files: CA-PIS_131-50XX_Catlac_White_Pre-Cat_Pigmented_Topcoat.pdf
Dry to Sand : 45 - 60 minutes
Dry to Stack: 12 hours
Tack Free Time: Flash off before entering oven
Dry to Sand: 30 - 45 minutes
VOC less exempt g/l: 623
VOC g/l: 547
Dry to Stack: 60 - 90 minutes
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Quick drying pre-catalyzed white lacquer offering good yellowing and chemical resistance.
spec_uses:
Used as a protective coatings for wood. For interior uses only.
Suggested Uses:
Spray
Mixing Ratio:
N/A
Pot Life: N/A
Application Viscosity:
22-24 sec Zahn #2 at 25°C
Reducer: 121-803 or 121-8020 if needed
Retarder: 800-5328 if needed
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: 3 to 5 mils wet
Coverage:
9 m²/l (95 pi²/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #2 signature cup 23 sec at 25°C
Flash Point: -20°C
Density (lb/gal): 0.99 ± 2% at 25°C
Solid (% by weight): 35%
Solid (% by volume): 22%
Shelf Life (months): 12

Catlac

131-50XX Catlac White Pre-Cat Pigmented Topcoat

Find distributor Trouver un distributeur

spec_description:

Quick drying pre-catalyzed white lacquer offering good yellowing and chemical resistance.

BACKRetour

Product codeCodes de produit
Product Codes:

131-5015 15° Low Gloss
131-5020 20° Low Gloss
131-5035 35° Satin
131-5050 50° Semi-Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 23 sec at 25°C
Flash Point: -20°C
Density (lb/gal): 0.99 ± 2% at 25°C
Solid (% by weight): 35%
Solid (% by volume): 22%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_131-50XX_Catlac_White_Pre-Cat_Pigmented_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more