Chemlife
522-2400 Chemlife® 24 White Post-Cat Pigmented Primer
Product Codes:

522-2400

Surface Preparation:

Substrate should be sanded with a #120, 150 or 180 grit stearated paper and free of dust and all contaminants. This primer cannot be used on metal, old oil or cellulose lacquers.

General Information:

Mix Chemlife 24 White Primer thoroughly, then catalyze and reduce material as recommended. Chemlife 24 White Primer must be well mixed while adding catalyst and reducers and must be agitated at all times to ensure product consistency. Chemlife 24 White Primer is applied in one or two coats and can be used as a primer for most wood and wood products meant for interior use. A thorough sanding using 240/320 grit stearated paper between coats is essential for adhesion. The second and subsequent coats must be applied the same day as the previous coat is sanded. Care should be taken to avoid sanding through the primer coat. With profiled edges, care must be taken with sanding of primer to avoid sanding through sharp edges. Complex profiles or profiles with sharp corners may cause difficulties in obtaining an effective primer coat of even thickness. In these cases, profile design must be discussed with your technical representative. Contact with metal surfaces should be avoided once the Chemlife 24 White Primer has been catalyzed. Recommended film build of Chemlife 24 White Primer is not to exceed 4 mils dry. Total recommended film build of Chemlife 24 White Primer and Chemlife 24 White Topcoat is not to exceed 6 mils dry.

Chemlife 24 White Primer must not be polluted with oil, varnish or the like and must not be sanded with steel wool between the coats. To obtain complete cure, the primer must be applied at a temperature above 18ºC and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surface must not be cleaned with ammonia containing products. This may accelerate discoloration.

Topcoats to use over 522-2400: Chemlife 24 White 117-24XX.

PDF Name: CA-PIS_522-2400_Chemlife_24_White_Post-Cat_Pigmented_Primer
Tack Free Time: 10 – 15 minutes
Files: CA-PIS_522-2400_Chemlife_24_White_Post-Cat_Pigmented_Primer.pdf
Dry to Sand : 60 minutes
Dry to Stack: 4 hours
Tack Free Time: Flash off before entering oven
test: 30 minutes
VOC less exempt g/l: 558
VOC g/l: 558
Dry to Stack: 60 minutes
Note: N/A
Note:

See individual compliance sheets for specific data

spec_description:

Chemlife 24 White - Primer is a fast drying, acid curing primer for interior use that gives a smooth, dense finish suitable for topcoating to produce very high quality pieces. Chemlife 24 provides an excellent base and is extremely easy to sand. Due to its 24 hour pot-life, Chemlife 24 White Primer provides the customer with minimum waste resulting in lower production costs.

spec_uses:

Chemlife 24 White Primer is designed for hardwoods and MDF. This product offers excellent filling properties as well as excellent vertical hang.

Suggested Uses:

Spray

Mixing Ratio:

10% 873-1251

Pot Life: 24 hours
Application Viscosity:

20-30 sec Zahn #2 at 25°C

Reducer: Lacquer Thinner 121-001/803-1339 or 121-8020 if needed
Retarder: 800-5328 EEP (2-3% maximum)
Clean-up Solvent: Lacquer thinner
Recommended Wet Film: 3 to 5 mils wet
Coverage:

14 m2/l (150 pi2/l) at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 42 sec at 25°C

Flash Point: 7°C
Density (lb/gal): 1.17 ± 2% at 25°C
Solid (% by weight): 52 ± 1%
Solid (% by volume): 35 ± 1%
Shelf Life (months): 12

Chemlife

522-2400 Chemlife® 24 White Post-Cat Pigmented Primer

Find distributor Trouver un distributeur

spec_description:

Chemlife 24 White - Primer is a fast drying, acid curing primer for interior use that gives a smooth, dense finish suitable for topcoating to produce very high quality pieces. Chemlife 24 provides an excellent base and is extremely easy to sand. Due to its 24 hour pot-life, Chemlife 24 White Primer provides the customer with minimum waste resulting in lower production costs.

Read more

Chemlife

522-2400 Chemlife® 24 White Post-Cat Pigmented Primer

spec_description:

Chemlife 24 White - Primer is a fast drying, acid curing primer for interior use that gives a smooth, dense finish suitable for topcoating to produce very high quality pieces. Chemlife 24 provides an excellent base and is extremely easy to sand. Due to its 24 hour pot-life, Chemlife 24 White Primer provides the customer with minimum waste resulting in lower production costs.

Read more
Product codeCodes de produit
Product Codes:

522-2400


Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 42 sec at 25°C

Flash Point: 7°C
Density (lb/gal): 1.17 ± 2% at 25°C
Solid (% by weight): 52 ± 1%
Solid (% by volume): 35 ± 1%
Shelf Life (months): 12

Download product information sheets

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Image

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Need help? Contact our team of wood coating experts.

Contact us