- V-Primer
- 546-7257 V-Primer Pigmented Vinyl Primer
- Product Codes:
546-7257
- Surface Preparation:
Wood must be sanded with a 120 or 150 grit paper and free of dust and all contaminants. Before the application of the topcoat, the V-Primer must be sanded with a 280/320 grit paper. This primer must not be applied over metal, old oil finish or nitrocellulose lacquer.
- General Information:
Agitate material before use. Keep under mixing to ensure product consistency. Apply one or two coats. A good sanding between coats with a #280/320 grit paper is necessary to obtain a good adhesion. This product could be catalyzed to enhance sanding properties but system must be evaluated and approved by AkzoNobel before going in production. For any information, contact your sales representative. If catalyzed, topcoat must be applied within 8 hours of sanding. Never apply more than 5 mils wet in one coat. Dry film thickness of V-Primer should not exceed 2 mils dry. Total dry film thickness of system should not exceed 5 mils dry.
To obtain complete cure, the primer must be applied at a temperature above 18ºC and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surface must not be cleaned with ammonia containing products.
Topcoats to use over 546-7257: 131-50XX, 131-51XX, 131-82XX, 117-30XX, 117-32XX, 421-67XX, 431-30XX, 484-6XXX, 421-72XX.
- PDF Name: CA-PIS_546-7257_V-Primer_Pigmented_Vinyl_Primer
- Tack Free Time: 45 - 60 minutes
- Files: CA-PIS_546-7257_V-Primer_Pigmented_Vinyl_Primer.pdf
- Dry to Sand : 60 - 90 minutes
- Dry to Stack: 3 - 4 hours
- Tack Free Time: Flash off before entering oven
- test: 45 - 60 minutes
- VOC less exempt g/l: 655
- VOC g/l: 584
- Dry to Stack: 1 - 2 hours
- Note:
See individual compliance sheets for specific data
- spec_description:
V-Primer is a pigmented one-component vinyl primer. It provides superior moisture resistance along with adhesion over all wood species.
- spec_uses:
V-Primer is recommended for kitchen cabinets, office or residential furniture as well as other interior wood applications.
- Suggested Uses: Spray
- Mixing Ratio:
N/A
- Pot Life: N/A
- Application Viscosity:
20 - 24 sec Zahn #2 at 25°C
- Reducer: Lacquer thinner 803-1339/121-001 or 121-8020
- Retarder: 800-5328 EEP
- Clean-up Solvent: Lacquer Thinner
- Recommended Wet Film: 3 - 5 mils wet
- Coverage:
8 m2/l (90 pi2/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.
- Note application:
N/A
- Viscosity:
Zahn #2 signature cup 22 sec at 25°C
- Flash Point: -20°C
- Density (lb/gal): 1.08 ± 2% at 25°C
- Solid (% by weight): 38 ± 1%
- Solid (% by volume): 20 ± 1%
- Shelf Life (months): 12
- V-Seal
- 546-5192 V-Seal Low VOC Clear Vinyl Sealer
- Product Codes:
546-5192 V-Seal
- Surface Preparation:
Wood must be sanded with a #120, 150 or 180 grit paper and free of dust and all contaminants. Before application of the topcoat, sealer must be sand with a 280/320 grit paper. V-Seal must not be used over metal, old oil finish or cellulosic finish.
- General Information:
Apply 3-4 mils wet on sanded surface by spray. If more than 4 mils, sanding becomes difficult. Never exceed a thickness of 5 mils by coat as the solvent will remain trapped in the film and this may cause stress in the film. Maximum film build of the sealer should not exceed 1 mil dry. Maximum film build of the system should not exceed 4 mils dry.
To obtain complete cure, the product must be applied at a temperature above 18ºC and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surface must not be cleaned with ammonia containing products.
V-seal is use with topcoat: 421-55XX, 421-63XX, 421-67XX, 421-72XX, 482-3XX, 431-22XX, 431-30XX, 431-90XX and 431-98XX.
- PDF Name: CA-PIS_546-5192_V-Seal_Low_VOC_Clear_Vinyl_Sealer
- Tack Free Time: 10 - 15 minutes
- Files: CA-PIS_546-5192_V-Seal_Low_VOC_Clear_Vinyl_Sealer.pdf
- Dry to Sand : 20 - 25 minutes
- Dry to Stack: 2 hours
- Tack Free Time: Flash off before entering oven
- test: 15 - 20 minutes
- VOC less exempt g/l: 724
- VOC g/l: 552
- Dry to Stack: 30 - 45 minutes
- Note:
See individual compliance sheets for specific data
- spec_description:
Low-VOC vinyl sealer. It is a single pack, quick drying product with excellent sanding and sealing properties. This product is recommended for Kitchen Cabinet or Furniture due to its excellent resistance to moisture. V-Seal contains no formaldehyde.
- spec_uses:
V-Seal is used for sealing wooden furniture and other wood surfaces for interior use only. It can be used on all wood types.
- Suggested Uses:
Spray
- Mixing Ratio:
N/A
- Pot Life: N/A
- Application Viscosity:
14-16 sec Zahn #2 at 25°C
- Reducer: Lacquer Thinner 803-1339/121-001 or 121-8020
- Retarder: 800-5328 EEP
- Clean-up Solvent: Lacquer Thinner
- Recommended Wet Film: 3 to 4 mils wet
- Coverage:
5 m2/l (50 pi2/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.
- Note application:
N/A
- Viscosity:
Zahn #2 signature cup 15 sec at 25°C
- Flash Point: -20°C
- Density (lb/gal): 0.89 ± 2% at 25°C
- Solid (% by weight): 17%
- Solid (% by volume): 12%
- Shelf Life (months): 12
- Chemseal
- 401-004 Chemseal Xtra Clear Vinyl Sealer
- Product Codes:
401-004 Chemseal
- Surface Preparation:
Wood must be sanded with a 120, 150 or 180 grit paper and free of dust and all contaminants. Stain systems under acid catalyzed coatings should be acid stable.
- General Information:
Apply 3-5 mils wet on sanded substrate. Allow one hour to dry at a minimum of 20ºC prior to topcoating. Sand with 280/320 grit paper before topcoating and ensure topcoat is applied within eight hours of sanding Chemseal.
Always mix Chemseal while adding catalyst and reducers in the recommended mixing ratios. Chemseal must be thoroughly agitated at all times to ensure product consistency. When catalyzed, avoid contact with metal surfaces.
Maximum film build of the sealer should not exceed 1 mil dry. Maximum film build of the system should not exceed 4 mils dry.
If used uncatalyzed, topcoat to use is 431-90XX. Catalyzed Chemseal can be overcoated with following topcoats: 421-55XX, 421-63XX, 421-67XX, 421-72XX, 482-3XX and 635-0XX.
To obtain complete cure, the product must be applied at a temperature above 18ºC and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surface must not be cleaned with ammonia containing products.
- PDF Name: CA-PIS_401-004_Chemseal_Xtra_Clear_Vinyl_Sealer
- Tack Free Time: 10 minutes
- Files: CA-PIS_401-004_Chemseal_Xtra_Clear_Vinyl_Sealer.pdf
- Dry to Sand : 1 hour
- Dry to Stack: 2 hours
- Tack Free Time: Flash off before entering oven
- test: 4 - 5 minutes
- VOC less exempt g/l: 716
- VOC g/l: 663
- Dry to Stack: 10 minutes
- Note:
See individual compliance sheets for specific data
- spec_description:
Chemseal 401-0040 is a ready-to-use vinyl sealer with good clarity and moisture resistance. It is a single pack, quick drying product with excellent sanding properties and is to be used where excellent adhesion is important.
- spec_uses:
Chemseal is used for sealing wooden furniture and other wood surfaces for interior use only. It can be used on all wood types.
- Suggested Uses:
Spray
- Mixing Ratio:
3% 999-017 if desired
- Pot Life: 8 hours if catalyzed
- Application Viscosity:
20-25 sec Zahn #2 at 25°C
- Reducer: 121-8020 or 121-803
- Retarder: 800-5328 EEP
- Clean-up Solvent: Lacquer Thinner
- Recommended Wet Film: 3-5 mils wet
- Coverage:
5 m2/l (55 pi2/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.
- Note application:
N/A
- Viscosity:
Zahn #2 signature cup 22 sec at 25°C
- Flash Point: -20°C
- Density (lb/gal): 0.88 ± 2% at 25°C
- Solid (% by weight): 18%
- Solid (% by volume): 13%
- Shelf Life (months): 12
- Chemseal
- 401-028 Chemseal Clear Vinyl Sealer
- Product Codes:
401-028 Chemseal
- Surface Preparation:
Wood must be sanded with a 120, 150 or 180 grit paper and free of dust and all contaminants. Stain systems under acid catalyzed coatings should be acid stable.
- General Information:
Apply 3-5 mils wet on sanded substrate. Allow one hour to dry at a minimum of 20ºC prior to topcoating. Sand with 280/320 grit paper before topcoating and ensure topcoat is applied within eight hours of sanding Chemseal.
Always mix Chemseal while adding catalyst and reducers in the recommended mixing ratios. Chemseal must be thoroughly agitated at all times to ensure product consistency. When catalyzed, avoid contact with metal surfaces.
If used uncatalyzed, topcoat to use is 431-90XX and 431-98XX. Catalyzed Chemseal can be overcoated with following topcoats: 421-55XX, 421-63XX, 421-72XX, 482-3XX and 635-0XX.
Maximum film build of the sealer should not exceed 1 mil dry. Maximum film build of the system should not exceed 4 mils dry.
To obtain complete cure, the product must be applied at a temperature above 18ºC and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surface must not be cleaned with ammonia containing products.
- PDF Name: CA-PIS_401-028_Chemseal_Clear_Vinyl_Sealer
- Tack Free Time: 10 minutes
- Files: CA-PIS_401-028_Chemseal_Clear_Vinyl_Sealer.pdf
- Dry to Sand : 1 hour
- Dry to Stack: 2 hours
- Tack Free Time: Flash off before entering oven
- test: 4 - 5 minutes
- VOC less exempt g/l: 714
- VOC g/l: 665
- Dry to Stack: 10 minutes
- Note:
See individual compliance sheets for specific data
- spec_description:
Chemseal 401-0280 is a ready-to-use vinyl sanding sealer with good clarity and moisture resistance. It is a single pack, quick drying product with excellent sanding properties and is to be used where excellent adhesion is important.
- spec_uses:
Chemseal is used for sealing wooden furniture and other wood surfaces for interior use only. It can be used on all wood types.
- Suggested Uses:
Spray
- Mixing Ratio:
3% 999-017 if desired
- Pot Life: 8 hours if catalyzed
- Application Viscosity:
20-25 sec Zahn #2 at 25°C
- Reducer: 121-8020 or 121-803
- Retarder: 800-5328 EEP
- Clean-up Solvent: Lacquer Thinner
- Recommended Wet Film: 3-5 mils wet
- Coverage:
5 m2/l (55 pi2/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.
- Note application:
N/A
- Viscosity:
Zahn #2 signature cup 26 sec at 25°C
- Flash Point: -20°C
- Density (lb/gal): 0.91 ± 2% at 25°C
- Solid (% by weight): 21%
- Solid (% by volume): 14%
- Shelf Life (months): 12
Need help? Contact our team of wood coating experts.
