Aqualac

423-44XX Aqualac II Waterborne Clear Topcoat

Product Codes:

423-4420 20°C Low Gloss
423-4435 35°C Satin
423-4450 50°C Semi-Gloss

Surface Preparation:

Sealer must be sanded with grit 120, 150 or 180 and free of dust and all contaminants.

General Information:

The first coat must be applied as is or reduced at 10% maximum with water. After 60 minutes of dry time, it must be sanded using a fine sand paper (ex.: 280,320) and free of sand dust. An extra coat is then applied, not reduced, depending on the desired wear resistance and the desired look. Additional coats must be done within 8 hours after sanding. Maximum film build of the system should not exceed 4 dry mils.

To obtain complete cure, the product must be applied at a temperature above 18°C and relative humidity below 65%. Contact with metallic surfaces must be avoided. Always use containers and equipment made of plastic or stainless steel to avoid discoloration of the material due to oxidation.

Keep from freezing.

PDF Name: CA-PIS_423-44XX_Aqualac_II_Waterborne_Clear_Topcoat

Tack Free Time: 30 - 45 minutes

Files: CA-PIS_423-44XX_Aqualac_II_Waterborne_Clear_Topcoat.pdf

Dry to Sand : 60 - 90 minutes

Dry to Stack: 24 hours

Tack Free Time: Flash off required before oven

test: 30 - 45 minutes

VOC less exempt g/l: 177

VOC g/l: 69

Dry to Stack: 6 - 8 hours

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

This fast dry high solid acrylic is a water based lacquer that can be used as a self-sealing lacquer. This product meets KCMA specifications (Kitchen Cabinet Manufacturer Association).

spec_uses:

For interior uses only.

Suggested Uses:

Spray

Mixing Ratio:

N/A

Pot Life: N/A

Application Viscosity:

29-30 sec Zahn #2 at 25°C

Reducer: 2% of water if needed

Retarder: N/A

Clean-up Solvent: Use water when in liquid state and water/acetone 800-5500 when material is semi-dried

Recommended Wet Film: 4 - 5 mils wet

Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #2 signature cup 29-30 sec at 25°C

Flash Point: > 93˚C (200F)

Density (lb/gal): 1.04 ± 2% at 25°C

Solid (% by weight): 35 ± 1%

Solid (% by volume): 31 ± 1%

Shelf Life (months): 6

Aqualac

423-44XX Aqualac II Waterborne Clear Topcoat

Find distributor Trouver un distributeur

spec_description:

This fast dry high solid acrylic is a water based lacquer that can be used as a self-sealing lacquer. This product meets KCMA specifications (Kitchen Cabinet Manufacturer Association).

BACK

Aqualac

423-44XX Aqualac II Waterborne Clear Topcoat

spec_description:

This fast dry high solid acrylic is a water based lacquer that can be used as a self-sealing lacquer. This product meets KCMA specifications (Kitchen Cabinet Manufacturer Association).

Product codeCodes de produit
Product Codes:

423-4420 20°C Low Gloss
423-4435 35°C Satin
423-4450 50°C Semi-Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 29-30 sec at 25°C

Flash Point: > 93˚C (200F)

Density (lb/gal): 1.04 ± 2% at 25°C

Solid (% by weight): 35 ± 1%

Solid (% by volume): 31 ± 1%

Shelf Life (months): 6

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_423-44XX_Aqualac_II_Waterborne_Clear_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap