FLEXGLAZE

825-49XX Promatch® FlexGlaze

Product Codes:

825-4900 Neutral Base

825-4901 Burnt Umber

825-4902 Black

825-4903 Yellow Oxide

825-4904 White

825-4905 Red Oxide

825-4906 Burnt Sienna

Surface Preparation:

Clean and sanded smooth with excess dust blown off.

Prior to use, mix Promatch FlexGlaze carefully and reduce viscosity by adding reducer as needed. Apply the reduced Glaze by spraying or with a rag. Allow two to three minutes air drying before wiping. Wipe clean and do not leave on any excess material that may interfere with optimum adhesion.

General Information:

FlexGlaze does not contain oil and is not combustible.

Can be tinted with 866 series colorants.

Dry Time: Glaze must dry 30 minutes prior to apply topcoat if wiped very clean. Glaze must dry 2 hours prior to applying topcoat if left heavy.

PDF Name: US-PIS_825-49XX_Promatch_FlexGlaze

Tack Free Time: N/A

Files: US-PIS_825-49XX_Promatch_FlexGlaze.pdf

Dry to Sand : N/A

Dry to Stack: N/A

Tack Free Time: N/A

VOC less exempt lb/gal: 4.9

Dry to Sand: N/A

VOC lb/gal: 4.9

VOC less exempt g/l: 575

VOC g/l: 575

VOC lb/lb Solid: 1.42

Dry to Stack: N/A

VHAPs lb/lb Solid: 0

Note: N/A

Note:

N/A

spec_description:

Promatch FlexGlaze is a very unique glaze. Promatch FlexGlaze has extended open time for workability. Extended open times for enhanced work ability and ease of use. Promatch FlexGlaze is able to be topcoated quicker than industry standard products. It has the ability to be uniformly blended. Works well over Chemcraft pigmented products and clears (not to be used direct to wood as a stain). Promatch FlexGlaze is compatible with all Chemcraft products for distribution, excluding waterborne.

spec_uses:

Promatch FlexGlaze can be used in the following interior applications:

Cabinetry

Furniture

Millwork

Recreational

Building Products

Suggested Uses:

To be used as a glaze only, under all Chemcraft distribution products (excluding Waterborne). Not to be used as a direct to wood stain. Can be tinted with 866 series colorants.

*Note - using 866 series colorants will increase VOCs.

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

N/A

Reducer: Neutral base or mineral spirits

Retarder: N/A

Clean-up Solvent: Thinner

Recommended Wet Film: N/A

Coverage:

Theoretical coverage - 491.65 (sq ft/dry mil @ 100% transfer efficiency.

Note application:

Spray or brush and wipe.

Viscosity:

77º F 2100-2500 CPS#3 Brookfield

Flash Point: 144º F (62ºC)

Density (lb/gal): 8.87

Solid (% by weight): 37.50 (+/- 1.00)

Solid (% by volume): 30.65 (+/- 1.00)

Shelf Life (months): 24

FLEXGLAZE

825-49XX Promatch® FlexGlaze

Find distributor Trouver un distributeur

spec_description:

BACK

FLEXGLAZE

825-49XX Promatch® FlexGlaze

spec_description:

Product codeCodes de produit
Product Codes:

825-4900 Neutral Base

825-4901 Burnt Umber

825-4902 Black

825-4903 Yellow Oxide

825-4904 White

825-4905 Red Oxide

825-4906 Burnt Sienna

Product information

Product specificationsSpécifications du produit

Viscosity:

77º F 2100-2500 CPS#3 Brookfield

Flash Point: 144º F (62ºC)

Density (lb/gal): 8.87

Solid (% by weight): 37.50 (+/- 1.00)

Solid (% by volume): 30.65 (+/- 1.00)

Shelf Life (months): 24

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_825-49XX_Promatch_FlexGlaze.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap