D-DUR White Pigmented Topcoat

620-10X D-Dur White PU Pigmented TC

Product Codes:

620-104 Matte

620-108 Gloss

Surface Preparation:

Primer should be sanded with 180 or 240 grit paper. Topcoat should be applied within 8 hours of sanding.

General Information:

Mix the desired amount of material and apply 3 - 5 mils wet.

The relative humidity in the application and drying rooms should never exceed 70%. Viscosity on the mixed material should be monitored regularly to maintain a consistent appearance.

Mixed product will contain 999-062, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials.

Total recommended film thickness of D-Dur system is not to exceed 6 mils dry.

PDF Name: US-PIS_620-10X_D-Dur_White_PU_Pigmented_TC

Tack Free Time: 10 - 15 minutes

Files: US-PIS_620-10X_D-Dur_White_PU_Pigmented_TC.pdf

Dry to Sand : 4 hours

Dry to Stack: Overnight (Complete curing is obtained after 7 days air dry)

Tack Free Time: 10 minutes

VOC less exempt lb/gal: 4.27

Dry to Sand: 2 hours

VOC lb/gal: 4.27

VOC less exempt g/l: 511

VOC g/l: 511

VOC lb/lb Solid: 0.68

Dry to Stack: Overnight (Complete curing is obtained after 7 days air dry)

VHAPs lb/lb Solid: 0.13

Note: N/A

Note:

N/A

spec_description:

D-Dur White Topcoat is a thixotropic, two-component polyurethane enamel with good durability, good resistance to chemicals and good weathering properties.

spec_uses:

This finish is recommended for wooden surfaces where good outdoor durability is desired (i.e., window frames, doors, wooden garden furniture).

Suggested Uses:

Wood Finish

Mixing Ratio:

4:1 with 999-062 (100 parts base to 25 parts 999-062)

Pot Life:

Approximately 4 hours depending on conditions. Pot life is decreased when product is hot or under pressure. Viscosity should be monitored after mixing with hardener.

Application Viscosity:

Zahn #2 signature 20 - 30 seconds

Reducer: 800-5301

Retarder: 800-5328

Clean-up Solvent: Lacquer Thinner (do not mix with product)

Recommended Wet Film: 3 - 5 wet mils

Coverage:

N/A

Note application:

N/A

Viscosity:

3000 cps at 77°F

Flash Point: 0°F

Density (lb/gal): 10.5

Solid (% by weight): 60%

Solid (% by volume): 42%

Shelf Life (months): 12

D-DUR White Pigmented Topcoat

620-10X D-Dur White PU Pigmented TC

Find distributor Trouver un distributeur

spec_description:

D-Dur White Topcoat is a thixotropic, two-component polyurethane enamel with good durability, good resistance to chemicals and good weathering properties.

BACK

D-DUR White Pigmented Topcoat

620-10X D-Dur White PU Pigmented TC

spec_description:

D-Dur White Topcoat is a thixotropic, two-component polyurethane enamel with good durability, good resistance to chemicals and good weathering properties.

Product codeCodes de produit
Product Codes:

620-104 Matte

620-108 Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:

3000 cps at 77°F

Flash Point: 0°F

Density (lb/gal): 10.5

Solid (% by weight): 60%

Solid (% by volume): 42%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_620-10X_D-Dur_White_PU_Pigmented_TC.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap