AQUAPRIME Pigmented Basecoat

550-1602 Aquaprime® II Neutral

Product Codes:

550-1602 Neutral

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit paper prior to coating. Aquaprime II Neutral should be sanded with 280/320 grit paper prior to being coated. Aquaprime II Neutral should be coated within (8) hours of being sanded for maximum adhesion. When recoating, the previous coat of Aquaprime II Neutral must be sanded and the next coat applied within (8) hours.

General Information:

Mix material before use. Add water to reduce if required and mix thoroughly. Apply by spray at 4 - 5 mils wet.

Aquaprime II Neutral must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces should be avoided. Keep from freezing.

Maximum film build of total coating system must not exceed 4 mils dry.

The completed coating system should be checked for required properties prior to start-up of production.

PDF Name: US-PIS_550-1602_Aquaprime_II_Neutral

Tack Free Time: 15 minutes

Files: US-PIS_550-1602_Aquaprime_II_Neutral.pdf

Dry to Sand : 45 minutes

Dry to Stack: 24 hours

Tack Free Time: 15 minutes @ room temperature

VOC less exempt lb/gal: <0.55

Dry to Sand: 15 minutes @ 110° F

VOC lb/gal: <0.29

VOC less exempt g/l: <65

VOC g/l: <35

VOC lb/lb Solid: <0.05

Dry to Stack: 15 minutes @ 140° F

VHAPs lb/lb Solid: <0.01

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

Aquaprime II Neutral is a ready to use waterborne primer. When tinted, Aquaprime II Neutral provides very good hiding when used as a primer only on hardwoods or MDF. Aquaprime II Neutral offers outstanding filling capabilities due to its high solid content at application (48% by volume). Aquaprime II Neutral provides an excellent base and is extremely easy to sand. After sanding it may be topcoated with any of Chemcraft topcoats, from waterborne, pre-catalyzed lacquer, post-catalyzed lacquer, varnish, and urethane.

spec_uses:

This product is designed for hardwoods or MDF. It is formulated especially for window and door frames, joinery pieces, and cabinets.

Suggested Uses:

Wood Primer

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 35 - 38 sec

Reducer: Use water as required. This product requires very little water to lower the viscosity.

Retarder: N/A

Clean-up Solvent: Use water when in liquid state. Use water / Butyl Cellosolve 800-5742 when material is semi-dried.

Recommended Wet Film: 4 - 5 wet mils

Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #2 signature cup 35 - 38 sec at 77°F

Flash Point: 149° F

Density (lb/gal): 12.1

Solid (% by weight): 64.4%

Solid (% by volume): 48.1%

Shelf Life (months): 12

AQUAPRIME Pigmented Basecoat

550-1602 Aquaprime® II Neutral

Find distributor Trouver un distributeur

spec_description:

BACK

AQUAPRIME Pigmented Basecoat

550-1602 Aquaprime® II Neutral

spec_description:

Product codeCodes de produit
Product Codes:

550-1602 Neutral

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 35 - 38 sec at 77°F

Flash Point: 149° F

Density (lb/gal): 12.1

Solid (% by weight): 64.4%

Solid (% by volume): 48.1%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_550-1602_Aquaprime_II_Neutral.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap