Aquaprime
550-1611 WB White Stainblock Primer
Product Codes:

550-1611

Surface Preparation: Substrate must be sanded using 120, 150 or 180 grit paper prior to coating. WB White Stainblock Primer should be sanded with 280/320 grit paper prior to being coated. WB White Stainblock Prime should be coated within (8) hours of being sanded for maximum adhesion. When recoating, the previous coat of WB White Stainblock Primer must be sanded and the next coat applied within (8) hours. 
General Information:

Mix material before use. Add water to reduce if required and mix thoroughly. Apply by spray at 4 - 5 mils wet.

WB White Stainblock Primer must be agitated thoroughly at all times to ensure product consistency.  Contact with metal surfaces should be avoided. 

Maximum film build of total coating system must not exceed 4 mils dry.

PDF Name: US-PIS_550-1611_WB_White_Stainblock_Primer
Tack Free Time: 15 minutes
Files: US-PIS_550-1611_WB_White_Stainblock_Primer.pdf
Dry to Sand : 45 minutes
Dry to Stack: 24 hours
Tack Free Time: 15 minutes @ room temperature
VOC less exempt lb/gal: <0.49
Dry to Sand: 15 minutes @ 110° F
VOC lb/gal: <0.25
VOC less exempt g/l: <58
VOC g/l: <30
VOC lb/lb Solid: <1.03
Dry to Stack: 15 minutes @ 140° F
VHAPs lb/lb Solid: <0.01
Note: N/A
Note:

See individual compliance sheets for specific data

spec_description:

WB White Stainblock Primer is a ready to use white waterborne primer.  WB White Stainblock Primer provides very good hiding when used as a primer only on hardwoods or MDF.  WB White Stainblock Primer offers excellent filling capabilities due to its high solid content at application (47% by volume).  WB White Stainblock Primer provides an excellent base and is extreamely easy to sand. After sanding it may be topcoated with any of the Chemcrat topcoats from waterborne, pre-catalyzed lacquer, post-catalyzed lacquer, varish and urethane. 

spec_uses:

This product is designed for hardwoods or MDF. It is formulated especially for windows and door frames, joinery pieces, and cabinets. Excellent primer for pre-primed jobs only. 


Suggested Uses:

Wood Primer

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 25-30 seconds

Reducer: Use water as required. This product requires very little water to lower the viscosity.
Retarder: N/A
Clean-up Solvent: Use water when in liquid state, use water / Butyl Cellosolve 800-5742 when material is semi-dried
Recommended Wet Film: 4 - 5 mils wet
Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #2 signature cup 25-30 sec at 77°F

Flash Point: >200° F
Density (lb/gal): 12.55
Solid (% by weight): 65%
Solid (% by volume): 47%
Shelf Life (months): 6
Aquaprime
550-1611 WB White Stainblock Primer
Product Codes:

550-1611

Surface Preparation: Substrate must be sanded using 120, 150 or 180 grit paper prior to coating. WB White Stainblock Primer should be sanded with 280/320 grit paper prior to being coated. WB White Stainblock Prime should be coated within (8) hours of being sanded for maximum adhesion. When recoating, the previous coat of WB White Stainblock Primer must be sanded and the next coat applied within (8) hours. 
General Information:

Mix material before use. Add water to reduce if required and mix thoroughly. Apply by spray at 4 - 5 mils wet.

WB White Stainblock Primer must be agitated thoroughly at all times to ensure product consistency.  Contact with metal surfaces should be avoided. 

Maximum film build of total coating system must not exceed 4 mils dry.

PDF Name: US-PIS_550-1611_WB_White_Stainblock_Primer
Tack Free Time: 15 minutes
Files: US-PIS_550-1611_WB_White_Stainblock_Primer.pdf
Dry to Sand : 45 minutes
Dry to Stack: 24 hours
Tack Free Time: 15 minutes @ room temperature
VOC less exempt lb/gal: <0.49
Dry to Sand: 15 minutes @ 110° F
VOC lb/gal: <0.25
VOC less exempt g/l: <58
VOC g/l: <30
VOC lb/lb Solid: <1.03
Dry to Stack: 15 minutes @ 140° F
VHAPs lb/lb Solid: <0.01
Note: N/A
Note:

See individual compliance sheets for specific data

spec_description:

WB White Stainblock Primer is a ready to use white waterborne primer.  WB White Stainblock Primer provides very good hiding when used as a primer only on hardwoods or MDF.  WB White Stainblock Primer offers excellent filling capabilities due to its high solid content at application (47% by volume).  WB White Stainblock Primer provides an excellent base and is extreamely easy to sand. After sanding it may be topcoated with any of the Chemcrat topcoats from waterborne, pre-catalyzed lacquer, post-catalyzed lacquer, varish and urethane. 

spec_uses:

This product is designed for hardwoods or MDF. It is formulated especially for windows and door frames, joinery pieces, and cabinets. Excellent primer for pre-primed jobs only. 


Suggested Uses:

Wood Primer

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 25-30 seconds

Reducer: Use water as required. This product requires very little water to lower the viscosity.
Retarder: N/A
Clean-up Solvent: Use water when in liquid state, use water / Butyl Cellosolve 800-5742 when material is semi-dried
Recommended Wet Film: 4 - 5 mils wet
Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #2 signature cup 25-30 sec at 77°F

Flash Point: >200° F
Density (lb/gal): 12.55
Solid (% by weight): 65%
Solid (% by volume): 47%
Shelf Life (months): 6
Aquaprime
550-1611 WB White Stainblock Primer
Product Codes:

550-1611

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit paper prior to coating. WB White Stainblock Primer should be sanded with 280/320 grit paper prior to being coated. WB White Stainblock Prime should be coated within (8) hours of being sanded for maximum adhesion. When recoating, the previous coat of WB White Stainblock Primer must be sanded and the next coat applied within (8) hours. 

General Information:

Mix material before use. Add water to reduce if required and mix thoroughly. Apply by spray at 4 - 5 mils wet.

WB White Stainblock Primer must be agitated thoroughly at all times to ensure product consistency.  Contact with metal surfaces should be avoided. 

Maximum film build of total coating system must not exceed 4 mils dry.

PDF Name: US-PIS_550-1611_WB_White_Stainblock_Primer
Tack Free Time: 15 minutes
Files: US-PIS_550-1611_WB_White_Stainblock_Primer.pdf
Dry to Sand : 45 minutes
Dry to Stack: 24 hours
Tack Free Time: 15 minutes @ room temperature
VOC less exempt lb/gal: <0.49
Dry to Sand: 15 minutes @ 110° F
VOC lb/gal: <0.25
VOC less exempt g/l: <58
VOC g/l: <30
VOC lb/lb Solid: <1.03
Dry to Stack: 15 minutes @ 140° F
VHAPs lb/lb Solid: <0.01
Note: N/A
Note:

See individual compliance sheets for specific data

spec_description:

WB White Stainblock Primer is a ready to use white waterborne primer.  WB White Stainblock Primer provides very good hiding when used as a primer only on hardwoods or MDF.  WB White Stainblock Primer offers excellent filling capabilities due to its high solid content at application (47% by volume).  WB White Stainblock Primer provides an excellent base and is extreamely easy to sand. After sanding it may be topcoated with any of the Chemcrat topcoats from waterborne, pre-catalyzed lacquer, post-catalyzed lacquer, varish and urethane. 

spec_uses:

This product is designed for hardwoods or MDF. It is formulated especially for windows and door frames, joinery pieces, and cabinets. Excellent primer for pre-primed jobs only. 


Suggested Uses:

Wood Primer

Mixing Ratio:

N/A

Pot Life: N/A
Application Viscosity:

Zahn #2 signature cup 25-30 seconds

Reducer: Use water as required. This product requires very little water to lower the viscosity.
Retarder: N/A
Clean-up Solvent: Use water when in liquid state, use water / Butyl Cellosolve 800-5742 when material is semi-dried
Recommended Wet Film: 4 - 5 mils wet
Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #2 signature cup 25-30 sec at 77°F

Flash Point: >200° F
Density (lb/gal): 12.55
Solid (% by weight): 65%
Solid (% by volume): 47%
Shelf Life (months): 12
Aquaprime
550-1611 WB White Stainblock Primer
Product Codes:

550-1611

Surface Preparation: Substrate must be sanded using 120, 150 or 180 grit paper prior to coating. WB White Stainblock Primer should be sanded with 280/320 grit paper prior to being coated. WB White Stainblock Prime should be coated within (8) hours of being sanded for maximum adhesion. When recoating, the previous coat of WB White Stainblock Primer must be sanded and the next coat applied within (8) hours. 
General Information:

Mix material before use. Add water to reduce if required and mix thoroughly. Apply by spray at 4 - 5 mils wet.

WB White Stainblock Primer must be agitated thoroughly at all times to ensure product consistency.  Contact with metal surfaces should be avoided. 

Maximum film build of total coating system must not exceed 4 mils dry.

PDF Name: US-PIS_550-1611_WB_White_Stainblock_Primer
Tack Free Time: 15 minutes
Files: US-PIS_550-1611_WB_White_Stainblock_Primer.pdf
Dry to Sand : 45 minutes
Dry to Stack: 24 hours
Tack Free Time: 15 minutes @ room temperature
VOC less exempt lb/gal: <0.49
Dry to Sand: 15 minutes @ 110° F
VOC lb/gal: <0.25
VOC less exempt g/l: <58
VOC g/l: <30
VOC lb/lb Solid: <1.03
Dry to Stack: 15 minutes @ 140° F
VHAPs lb/lb Solid: <0.01
Note: N/A
Note:

See individual compliance sheets for specific data

spec_description:

WB White Stainblock Primer is a ready to use white waterborne primer.  WB White Stainblock Primer provides very good hiding when used as a primer only on hardwoods or MDF.  WB White Stainblock Primer offers excellent filling capabilities due to its high solid content at application (47% by volume).  WB White Stainblock Primer provides an excellent base and is extreamely easy to sand. After sanding it may be topcoated with any of the Chemcrat topcoats from waterborne, pre-catalyzed lacquer, post-catalyzed lacquer, varish and urethane. 

spec_uses:

This product is designed for hardwoods or MDF. It is formulated especially for windows and door frames, joinery pieces, and cabinets. Excellent primer for pre-primed jobs only. 


Suggested Uses:

Wood Primer

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 25-30 seconds

Reducer: Use water as required. This product requires very little water to lower the viscosity.
Retarder: N/A
Clean-up Solvent: Use water when in liquid state, use water / Butyl Cellosolve 800-5742 when material is semi-dried
Recommended Wet Film: 4 - 5 mils wet
Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #2 signature cup 25-30 sec at 77°F

Flash Point: >200° F
Density (lb/gal): 12.55
Solid (% by weight): 65%
Solid (% by volume): 47%
Shelf Life (months): 6
Acquaduro
550-1761 Acquaduro™ 1K Waterborne Neutral Primer
Product Codes:

550-1761

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit paper prior to coating. Acquaduro™ 1K Waterborne Neutral Primer should be sanded with 280/320 grit paper prior to being coated. Acquaduro™ 1K Waterborne Neutral Primer should be coated within (8) hours of being sanded for maximum adhesion.


General Information:

Mix material before use. Add water to reduce if required and mix thoroughly. Apply by spray at 4 - 6 mils wet. Acquaduro™ 1K Waterborne Neutral Primer must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces should be avoided. Maximum film build of total coating system must not exceed 4 mils dry.

PDF Name: US-PIS_550-1761_Acquaduro_1K_Waterborne_Neutral_Primer
Tack Free Time: 10 minutes
Files: US-PIS_550-1761_Acquaduro_1K_Waterborne_Neutral_Primer.pdf
Dry to Sand : 20 minutes
Dry to Stack: 12 hours
Tack Free Time: 5 minutes
VOC less exempt lb/gal: 0.36
Dry to Sand: 10 minutes
VOC lb/gal: 0.16
VOC less exempt g/l: 48.0
VOC g/l: 19.0
VOC lb/lb Solid: 0.02
Dry to Stack: 30 minutes
VHAPs lb/lb Solid: 0.00
Note: N/A
Note:

N/A

spec_description:

Acquaduro™ 1K Neutral Primer is a ready to use neutral waterborne primer. This waterborne primer provides excellent durability and water resistance on hardwoods or MDF. Acquaduro Waterborne Primer has great ease of application and fast application and dry times.
Recommended topcoat is the Acquaduro 2K Pigmented Polyurethane Waterborne Topcoat.

spec_uses:

Acquaduro™ 1K Waterborne Neutral Primer has been designed for the cabinet, architectural millwork, furniture and refinish markets.

Suggested Uses: Designed for use on hardwoods or MDF
Mixing Ratio:

N/A

Pot Life: N/A
Application Viscosity:

Zahn #2 Signature cup 30-35 sec at 77º F (25º C)


Reducer: Use water if required
Retarder: 970-1358 1 to 3 % by Volume
Clean-up Solvent: Water
Recommended Wet Film: 4-6 wet mils
Coverage:

610 sqft/gal

Note application:

N/A

Viscosity:

Zahn #2 Signature Cup 30-35 seconds at 77ºF (25ºC)

Flash Point: >200°F (93.3°C)
Density (lb/gal): 11.31
Solid (% by weight): 56.4
Solid (% by volume): 40.7
Shelf Life (months): 12

Need help? Contact our team of wood coating experts.

Contact us