- Acquaduro
- 550-1761 Acquaduro™ 1K Waterborne Neutral Primer
- Product Codes:
550-1761
- Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit paper prior to coating. Acquaduro™ 1K Waterborne Neutral Primer should be sanded with 280/320 grit paper prior to being coated. Acquaduro™ 1K Waterborne Neutral Primer should be coated within (8) hours of being sanded for maximum adhesion.
- General Information:
Mix material before use. Add water to reduce if required and mix thoroughly. Apply by spray at 4 - 6 mils wet. Acquaduro™ 1K Waterborne Neutral Primer must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces should be avoided. Maximum film build of total coating system must not exceed 4 mils dry.
- PDF Name: US-PIS_550-1761_Acquaduro_1K_Waterborne_Neutral_Primer
- Tack Free Time: 10 minutes
- Files: US-PIS_550-1761_Acquaduro_1K_Waterborne_Neutral_Primer.pdf
- Dry to Sand : 20 minutes
- Dry to Stack: 12 hours
- Tack Free Time: 5 minutes
- VOC less exempt lb/gal: 0.36
- Dry to Sand: 10 minutes
- VOC lb/gal: 0.16
- VOC lb/lb Solid: 0.02
- Dry to Stack: 30 minutes
- VHAPs lb/lb Solid: 0.00
- Note:
N/A
- spec_description:
Acquaduro™ 1K Neutral Primer is a ready to use neutral waterborne primer. This waterborne primer provides excellent durability and water resistance on hardwoods or MDF. Acquaduro Waterborne Primer has great ease of application and fast application and dry times.
Recommended topcoat is the Acquaduro 2K Pigmented Polyurethane Waterborne Topcoat. - spec_uses:
Acquaduro™ 1K Waterborne Neutral Primer has been designed for the cabinet, architectural millwork, furniture and refinish markets.
- Suggested Uses: Designed for use on hardwoods or MDF
- Mixing Ratio:
N/A
- Pot Life: N/A
- Application Viscosity:
Zahn #2 Signature cup 30-35 sec at 77º F (25º C)
- Reducer: Use water if required
- Retarder: 970-1358 1 to 3 % by Volume
- Clean-up Solvent: Water
- Recommended Wet Film: 4-6 wet mils
- Coverage:
610 sqft/gal
- Note application:
N/A
- Viscosity:
Zahn #2 Signature Cup 30-35 seconds at 77ºF (25ºC)
- Flash Point: >200°F (93.3°C)
- Density (lb/gal): 11.31
- Solid (% by weight): 56.4
- Solid (% by volume): 40.7
- Shelf Life (months): 12
- Acquaduro
- 228-36XX Acquaduro™ Neutral 2K Polyurethane Waterborne Topcoat
- Product Codes:
228-3610 Matte
228-3620 Low Gloss
228-3635 Satin
228-3650 Semi-Gloss
228-3680 Gloss - Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit paper prior to priming. Primer should be sanded with 280/320 grit paper prior to being coated, The Primer should be coated within eight hours of being sanded. Appropriate primers are the Chemcraft Acquaduro™ Primer 550-1760 or 550-1761. When recoating, the previous coat of the Acquaduro™ 2K Polyurethane Waterborne Topcoat must be sanded and the next coat applied within eight hours of being sanded.
- General Information:
**After mixing part A and part B to the correct ratio, water can then be added to reduce viscosity prior to application as needed depending on spray equipment. A maximum of 10% water can be added to the fresh (immediately after the part B is fully dispersed into part A) catalyzed material.
Note: Adding extra water during application is not recommended as this will have a direct impact on the pot life. The pot life of the mixture will be reduced significantly, and the mixture will gel quickly.
The mixed product contains 876-3400, an isocyanate-based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detailed information. Product must be thoroughly stirred before adding the hardener in the recommended ratio. The viscosity of the product should be monitored after mixing with the hardener. The relative humidity in the application and drying room should not exceed 75% for maximum coating performance. - PDF Name: US-PIS_228-36XX_Acquaduro_Neutral_2K_Polyurethane_Waterborne_Topcoat
- Tack Free Time: 20 minutes
- Files: US-PIS_228-36XX_Acquaduro_Neutral_2K_Polyurethane_Waterborne_Topcoat.pdf
- Dry to Sand : 45 minutes
- Dry to Stack: 24 hours
- Tack Free Time: 12 minutes
- VOC less exempt lb/gal: 0.67
- Dry to Sand: 20 minutes
- VOC lb/gal: 0.22
- VOC lb/lb Solid: 0.07
- Dry to Stack: 30 minutes
- VHAPs lb/lb Solid: 0.00
- Note:
N/A
- spec_description:
Acquaduro™ is a neutral 2K polyurethane waterborne topcoat for industrial application. This product is a neutral base to be tint to any desired color. This product provides excellent water and chemical resistance. Whether you are at the finishing shop or at a professional on-site job this low VOC and low odor system meets or exceeds industry standards.
- spec_uses:
Acquaduro™ Neutral 2K Polyurethane Waterborne Topcoat has been designed for cabinet,
architectural millwork, furniture and refinish markets. - Suggested Uses: For cabinet, architectural millwork, furniture, refinish markets
- Mixing Ratio:
8% by volume of 876-3400 hardener
- Pot Life: 3-4 hours depending on external condition
- Application Viscosity:
Zahn #3 Signature cup 30-35 sec at 77°F (25°C)
- Reducer: Water up to 10% by volume
- Retarder: 870-1358 1 to 3 % by volume
- Clean-up Solvent: Water
- Recommended Wet Film: 4-5 wet mils
- Coverage:
560 sqft/gal
- Note application:
Polyurethane base should be thoroughly mixed first then hardener must be slowly added during agitation, product must be mixed for 1-2 minutes.
Customer must wait 5 minutes for "induction time" before usage. Mix only what you can use for 2-3 hours at a time.
If an excessive amount over 5 wet mils is applied, there is a chance that surface imperfection (mud cracking, etc.) may result.
- Viscosity:
Zahn #2 Signature cup 40-45 sec at 77°F (25°C)
Zahn #3 Signature cup 18-22 sec at 77°F (25°C) - Flash Point: >200°F
- Density (lb/gal): 8.78
- Solid (% by weight): 33.5
- Solid (% by volume): 29.5
- Shelf Life (months): 12
- Acquaduro
- 550-3400 Acquaduro™ 2K Polyurethane Waterborne Primer
- Product Codes:
550-3400
- Surface Preparation:
Substrate should be sanded using 120, 150 or 180 grit stearated paper. Acquaduro™ 2K PU WB Primer cannot be used on metal, old oil or nitrocellulose lacquers. For optimum results use 228-34XX Acquaduro™ Pigmented 2K PU TC or 423-34XX Acquaduro™ Clear 2K PU TC. When recoating, the previous coat of Acquaduro™ 2K PU WB Primer must be sanded and the next coat applied within eight hours of being sanded.
- General Information:
The mixed product contains 876-3400, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detail information. Oil stains must be avoided because they will interfere with the adhesion. Product must be thoroughly stirred before adding the hardener in the recommended ratio. The viscosity of the product should be monitored after mixing with the hardener. The relative humidity in the application and drying room should not exceed 75% for maximum coating performance.
- PDF Name: US-PIS_550-3400_Acquaduro_2K_Polyurethane_Waterborne_Primer
- Tack Free Time: 20 - 30 minutes
- Files: US-PIS_550-3400_Acquaduro_2K_Polyurethane_Waterborne_Primer.pdf
- Dry to Sand : 60 minutes
- Dry to Stack: 3 - 4 hours
- Tack Free Time: 15 - 20 minutes
- VOC less exempt lb/gal: 0.81
- Dry to Sand: 30 - 45 minutes
- VOC lb/gal: 0.36
- VOC lb/lb Solid: 0.06
- Dry to Stack: 60 - 90 minutes
- VHAPs lb/lb Solid: 0.01
- Note:
N/A
- spec_description:
Acquaduro™ 2K PU WB Primer is a 2 component polyurethane primer for interior wood woodwork and MDF. The formulation provides superior build, sag resistance, coverage. Acquaduro is easy to apply, provides very smooth surface with minimal sanding requirement.
- spec_uses:
Acquaduro™ 2K PU WB Primer is designed for the cabinet, architectural millwork, furniture and refinish markets.
- Suggested Uses: Interior wood finishes
- Mixing Ratio:
7% 876-3400 Hardener by volume
- Pot Life: 3 hours
- Application Viscosity:
Zahn #3 Signature Cup 18-22 sec at 77˚F (25˚C)
- Reducer: Water 3 - 5%
- Retarder: 870-1358
- Clean-up Solvent: Water
- Recommended Wet Film: 4 - 5 mils
- Coverage:
638.68 sqft/gal.
- Note application:
N/A
- Viscosity:
Zahn #3 Signature Cup 18-22 sec at 77˚F (25˚C)
- Flash Point: >201°F
- Density (lb/gal): 11.44
- Solid (% by weight): 56.44
- Solid (% by volume): 39.8
- Shelf Life (months): 12
- Acquaduro
- 423-34XX Acquaduro™ Clear 2K Polyurethane Waterborne Topcoat
- Product Codes:
423-3405
423-3410
423-3420
423-3435
423-3450
423-3480
- Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit paper prior to staining or coating. Sealer should be sanded with 280/320 grit paper prior to being coated, The sealer should be coated within eight hours of being sanded. Self-seal is recommended. When recoating, the previous coat of the Acquaduro™ Clear 2K Polyurethane Waterborne Topcoat must be sanded and the next coat applied within eight hours of being sanded. Recommended stain systems include Promatch Aqua and Promatch C-Mix.
- General Information:
**After mixing part A and part B to the correct ratio, water can then be added to reduce viscosity prior to application as needed depending on spray equipment. A maximum of 10% water can be add to the fresh (immediately after the part B is fully dispersed into part A) catalyzed material.
Note: Adding extra water during application is not recommended as this will have a direct impact on the pot life. The pot life of the mixture will be reduce significantly and the mixture will gel quickly.
The mixed product contains 876-3400, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detail information. Product must be thoroughly stirred before adding the hardener in the recommended ratio. Oil stains must be avoided because they will interfere with the adhesion. The viscosity of the product should be monitored after mixing with the hardener. The relative humidity in the application and drying room should not exceed 75% for maximum coating performance. - PDF Name: US-PIS_423-34XX_Acquaduro_Clear_2K_Polyurethane_Waterborne_Topcoat
- Tack Free Time: 20 minutes
- Files: US-PIS_423-34XX_Acquaduro_Clear_2K_Polyurethane_Waterborne_Topcoat.pdf
- Dry to Sand : 45 minutes
- Dry to Stack: 24 hours
- Tack Free Time: 10 minutes
- VOC less exempt lb/gal: 1.38
- Dry to Sand: 20 minutes
- VOC lb/gal: 0.53
- VOC lb/lb Solid: 0.17
- Dry to Stack: 30 minutes
- VHAPs lb/lb Solid: 0.00
- Note:
N/A
- spec_description:
Acquaduro™ is a clear 2K polyurethane waterborne topcoat for industrial application. This product provides excellent water and chemical resistance and has high build and excellent feel and appearance. In addition to the enhanced durable features, our 2k waterborne polyurethane topcoat is easy to apply, offers great sandability and has no recoat window. Whether you are at a finishing shop or at a professional on-site job this low VOC and low odor product meets or exceeds industry standards.
- spec_uses:
Acquaduro™ Clear 2K Polyurethane Waterborne Topcoat has been designed for the cabinet, architectural millwork, furniture and refinish markets.
- Suggested Uses: For cabinet, architectural millwork, furniture, refinish markets.
- Mixing Ratio:
8% by volume of 876-3400 Hardener
**See Application Data Notes section for additional mixing information** - Pot Life: 4 hours at 77°F (25° C)
- Application Viscosity:
Zahn #2 Signature cup 45-50 sec at 77°F (25° C)
Zahn #3 Signature cup 20-25 sec at 77°F (25° C) - Reducer: Water up to 10% by volume
- Retarder: 870-1358 1 to 3% by volume
- Clean-up Solvent: Water
- Recommended Wet Film: 5-6 wet mils
- Coverage:
510 sqft/gal
- Note application:
Polyurethane base should be thoroughly mixed first then Hardener must be Slowly added during agitation, product must be mixed for 1-2 minutes.
Customer must wait 5 minutes for “induction time” before usage. Mix only what you can use for 1 to 2 hours at a time.
- Viscosity:
Zahn #2 Signature cup 31-35 sec at 77°F (25°C)
Zahn #3 Signature cup 14-18 sec at 77°F (25°C) - Flash Point: > 200°F (93.3°C)
- Density (lb/gal): 8.77
- Solid (% by weight): 35.7
- Solid (% by volume): 31.8
- Shelf Life (months): 12
- AQUAPRIME Pigmented Basecoat
- 550-2200 Aquaprime® WB Stain Blocking Primer
- Product Codes:
550-2200
- Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit paper prior to coating. Aquaprime WB Stain Blocking Primer should be sanded with 280/320 grit paper prior to being coated. Aquaprime WB Stain Blocking Primer should be coated within (8) hours of being sanded for maximum adhesion. When recoating, the previous coat of Aquaprime WB Stain Blocking Primer must be sanded and the next coat applied within (8) hours.
Before applying any solvent borne topcoats, ensure the primer is thoroughly dry by allowing it to dry a minimum of 2 hours
- General Information:
Mix material before use. Add water to reduce if required and mix thoroughly. Apply by spray at 4 - 5 mils wet. Aquaprime WB Stain Blocking Primer must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces should be avoided. Maximum film build of total coating system must not exceed 4 mils dry. The completed coating system should be checked for required properties prior to start-up of production.
- PDF Name: US-PIS_550-2200_Aquaprime_WB_Stain_Blocking_Pigmented_Primer
- Tack Free Time: 15 minutes
- Files: US-PIS_550-2200_Aquaprime_WB_Stain_Blocking_Pigmented_Primer.pdf
- Dry to Sand : 45 minutes
- Dry to Stack: 24 hours
- Tack Free Time: 15 minutes @ room temperature
- VOC less exempt lb/gal: >0.55
- Dry to Sand: 15 minutes @ 110° F
- VOC lb/gal: <0.29
- VOC lb/lb Solid: <0.05
- Dry to Stack: 15 minutes @ 140° F
- VHAPs lb/lb Solid: <0.01
- Note:
See individual compliance sheets for specific data
- spec_description:
Aquaprime WB Stain Blocking Primer is a ready to use white waterborne stain blocking primer. Aquaprime Basecoat provides very good hiding when used as a primer only on hardwoods or MDF. Aquaprime WB Stain Blocking Primer offers excellent filling capabilities due to its high solid content at application (45.5% by volume). Aquaprime WB Stain Blocking Primer provides an excellent base and is extremely easy to sand.
After sanding it may be topcoated with any Chemcraft topcoat from waterborne, pre-catalyzed lacquer, post-catalyzed lacquer, varnish, and urethane. - spec_uses:
This product is designed for hardwoods or MDF. It is formulated especially windows and door frames, joinery pieces, and cabinets. Excellent primer when used in conjunction with Aquawhite or for pre-primed jobs only.
- Suggested Uses: Wood Primer
- Mixing Ratio:
N/A
- Pot Life: N/A
- Application Viscosity:
Zahn #3 (EZ) cup 16-22 sec at 77°F
- Reducer: Use water as required. This product requires very little water to lower the viscosity.
- Retarder: N/A
- Clean-up Solvent: Use water when in liquid state. Use water / Butyl Cellosolve 800-5742 when material is semi-dried.
- Recommended Wet Film: 4-5 wet mils
- Coverage:
N/A
- Note application:
If tannin bleed is noticed on the first coat of primer, let material dry overnight. Sand the following day and apply a second coat of 550-2200, then sand and apply the recommended Chemcraft WB topcoat the next day for optimal performance in holding back tannin.
- Viscosity:
Zahn #3 (EZ) cup 16-22 sec at 77°F
- Flash Point: >200°F
- Density (lb/gal): 12.66
- Solid (% by weight): 64.3%
- Solid (% by volume): 45.5%
- Shelf Life (months): 12
Need help? Contact our team of wood coating experts.
