Waterborne 1K

228-27XX Waterborne 1K Neutral Topcoat

Product Codes:

228-2705 Flat
228-2710 Matte
228-2720 Low Gloss
228-2735 Satin
228-2750 Semi-Gloss
228-2790 High Gloss

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit paper prior to prime. Primer should be sanded with 280/320 grit paper prior to being coated. The primer should be coated within eight hours of sanding.

Appropriate primers are the Chemcraft 550-3500, 550-3501, 550-1600, 550-1602, 550-1760, and 550-1761. Always recoat within eight hours of sanding.

General Information:

N/A

PDF Name: US-PIS_228-27XX_Waterborne_1K_Neutral_Topcoat

Tack Free Time: 30 minutes

Files: US-PIS_228-27XX_Waterborne_1K_Neutral_Topcoat.pdf

Dry to Sand : 60 minutes

Dry to Stack: 24 hours

Tack Free Time: 15 minutes

VOC less exempt lb/gal: 1.71

Dry to Sand: 30 minutes

VOC lb/gal: 0.69

VOC less exempt g/l: 205

VOC g/l: 083

VOC lb/lb Solid: 0.23

Dry to Stack: 60 minutes

VHAPs lb/lb Solid: 0.00

Note: N/A

Note:

N/A

spec_description:

Waterborne 1K Neutral Topcoat is an acrylic selfcrosslinking product that is utilized in various markets. Waterborne 1K Neutral Topcoat meets AWI system #7 and specific KCMA requirements. Waterborne 1K Neutral Topcoat has unique thixotropy for vertical and horizontal application. Waterborne 1K Neutral Topcoat has excellent hiding properties. Waterborne MaestroHue complete color sytem available utilizing 897 colorants at a maximum 7%.

spec_uses:

Waterborne 1K Neutral Topcoat is designed for cabinets, architectural millwork, furniture and refinish markets.

Suggested Uses: For cabinets, architectural millwork, furniture, refinish markets

Mixing Ratio:

N/A

Pot Life: N/A

Application Viscosity:

55-60 seconds Zahn signature #4

Reducer: Water up to 10% by volume depending on spray equipment

Retarder: 803-1462 1 to 3% by volume as needed

Clean-up Solvent: Water

Recommended Wet Film: 4-6 wet mils

Coverage:

503 Sqft/gal

Note application:

Depending on spray equipment the Waterborne 1K Neutral Topcoat may need some reduction - up to 10% with water. Recommended for cup gun, gravity cup or HVLP. For Air Assisted Airless Waterborne 1K Clear Topcoat can be used as is.

Viscosity:

1100-1300 Centipoises at 77°F (25°C)

Flash Point: >200°F

Density (lb/gal): 8.55

Solid (% by weight): 34.73

Solid (% by volume): 31.3

Shelf Life (months): 12

Waterborne 1K

228-27XX Waterborne 1K Neutral Topcoat

Find distributor Trouver un distributeur

spec_description:

BACKRetour

Waterborne 1K

228-27XX Waterborne 1K Neutral Topcoat

spec_description:

Product codeCodes de produit
Product Codes:

228-2705 Flat
228-2710 Matte
228-2720 Low Gloss
228-2735 Satin
228-2750 Semi-Gloss
228-2790 High Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:

1100-1300 Centipoises at 77°F (25°C)

Flash Point: >200°F

Density (lb/gal): 8.55

Solid (% by weight): 34.73

Solid (% by volume): 31.3

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_228-27XX_Waterborne_1K_Neutral_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap