Agitate material before use. Always mix Chemvinyl 275 while adding hardener and reducers in the recommended mixing ratios. Chemvinyl 275 must be agitated thoroughly at all times to ensure product consistency. When catalyzed, avoid contact with metal surfaces.

Apply at 3-5 mils wet on sanded substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper.

Maximum film build of Chemvinyl 275 should not exceed 1.5 mils dry. Maximum film build of total catalyzed coating system must not exceed 4 mils dry.

Chemvinyl 275 should not be used and dried at temperatures below 64°F or relative humidity above 65%.

Agitate material before use. Always mix ProVinyl Vinyl Primer while adding reducers in the recommended levels. ProVinyl Vinyl Primer must be agitated thoroughly at all times to ensure product consistency.Apply at 3 – 5 mils wet sanded substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper.

Provinyl  Vinyl Primer uncatalyzed can be topcoated with only pre-catalyzed topcoats. Provinyl  Vinyl primer catalyzed can be topcoated with Pre-Catalyzed or Conversion Varnish topcoats.

Maximum film build of ProVinyl Vinyl Primer should not exceed 2 mils dry. Contact with metal surfaces should be avoided. ProVinyl Vinyl Primer must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats. ProVinyl Vinyl Primer must not be used and dried at temperatures below 64°F or relative humidity above 65%. During the curing process, the coating must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finish surfaces. This may accelerate discoloration.

Agitate material thoroughly before use. Chemvinyl must be agitated thoroughly at all times to ensure product consistency.

Apply one or two coats at 3-5 mils wet and allow 30 – 45 minutes dry at 68°F prior to sanding and applying next coating. Sand with 280/320 grit paper before top coating or re-coating and ensure next coat is applied within eight hours of sanding Chemvinyl.

Chemvinyl may be topcoated with pre-catalyzed topcoats such as 431-80XX, 431-46XX, 431-47XX and 431-70XX. Chemvinyl has a limited shelf life and should be used within six months.

Chemvinyl must not be polluted with oil, varnish or  the like and must not be sanded with steel wool between the coats. Chemvinyl must not be used nor dried at temperatures below 64°F (18°C), or relative air humidity above 65%. During hardening, the sealer must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finished surface.

Maximum film build of Chemvinyl 431-1923 is not to exceed 2 mils dry.

Apply at 3 – 5 wet mils on sanded substrate. Maximum film build of 546-7023 is not to exceed 1 mil dry. Allow one hour to dry at a minimum of 68°F prior to topcoating.

Sand with 280/320 grit paper before topcoating and ensure topcoat is applied the same day the sanding is done.

Always mix Chemvinyl HS while adding hardener and reducers in the recommended mixing ratios. Chemvinyl HS must be thoroughly agitated at all times to ensure product consistency. When catalyzed, avoid contact with metal surfaces.

Chemvinyl HS is used for sealing wooden furniture and other wood surfaces for interior use only. It can be used on all wood types and after drying and sanding, may be overcoated with acid curing systems such as Danspeed 424-44XX, 424-45XX, Plastofix Light 421-48XX or E-Var 421-80XX.

In some instances, uncatalyzed materials containing nitrocellulose may show poor adhesion when coating over Chemvinyl HS. The time lag between sealing and recoating in these cases is critical and systems must be checked to ensure adequate film properties.