PROMATCH® C-Mix

825-9300 Promatch® C-Mix 240 Stain Base

Product Codes:

825-9300 Clear Base

Surface Preparation:

Wood substrate should be sanded with 120, 150 or 180 grit paper prior to staining or coating. On woods such as maple, coarser sanding, such as 150 grit, should be performed to avoid polishing of the wood surface. Hand sanding in the direction of the grain following orbital sanding will remove swirl marks.

General Information:

Application may be by hand or spray. These stains must be wiped into the grain and wiped clean with a clean rag to ensure good adhesion by subsequent clear coats.

The VOC levels of the stain are such that they can be tinted up to 12% by weight and remain 275 compliant.

These products may be clear coated with any of the following systems: All waterborne, pre-catalyzed lacquer, post-catalyzed lacquer, varnish from Chemcraft as well as the sealers associated with these systems.

These stains demonstrate good open time to allow for uniform appearance on large pieces.

Product must be thoroughly agitated before use.

PDF Name: US-PIS_825-9300_Promatch_C-Mix_240_Stain_Base

Tack Free Time: N/A

Files: US-PIS_825-9300_Promatch_C-Mix_240_Stain_Base.pdf

Dry to Sand : N/A

Dry to Stack: N/A

Tack Free Time: N/A

VOC less exempt lb/gal: 0.19

Dry to Sand: N/A

VOC lb/gal: 1.06

VOC less exempt g/l: 23

VOC g/l: 127

VOC lb/lb Solid: 0.14

Dry to Stack: N/A

VHAPs lb/lb Solid: 0.01

Note: N/A

Note:

N/A

spec_description:

Promatch C-Mix 240 Stain Base is an all-purpose wipe stain for furniture and cabinets that is formulated to low levels of VOC for application in regulated areas. Application may be by hand or spray. Promatch C-Mix 240 stains offer a simple one step stain color base, good clarity and grain fill with ease of workability.

spec_uses:

Stain for interior wood finishing.

Suggested Uses:

Wood Stain

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

N/A

Reducer: 825-9300

Retarder: N/A (or compliant solvent)

Clean-up Solvent: Acetone

Recommended Wet Film: N/A

Coverage:

N/A

Note application:

N/A

Viscosity:

13-17 sec., Zahn #2 @77°F

Flash Point: -4°F (-16°C)

Density (lb/gal): 9.85

Solid (% by weight): 14%

Solid (% by volume): 15%

Shelf Life (months): 24

PROMATCH® C-Mix

825-9300 Promatch® C-Mix 240 Stain Base

Find distributor Trouver un distributeur

spec_description:

BACK

PROMATCH® C-Mix

825-9300 Promatch® C-Mix 240 Stain Base

spec_description:

Product codeCodes de produit
Product Codes:

825-9300 Clear Base

Product information

Product specificationsSpécifications du produit

Viscosity:

13-17 sec., Zahn #2 @77°F

Flash Point: -4°F (-16°C)

Density (lb/gal): 9.85

Solid (% by weight): 14%

Solid (% by volume): 15%

Shelf Life (months): 24

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_825-9300_Promatch_C-Mix_240_Stain_Base.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap