CHEMLIFE 24 PLUS Tint Base TC
117-27XX CHEMLIFE® 24 PLUS CV Clear Tint Base TC
Product Codes:

117-2705 Flat
117-2720 Low Gloss
117-2735 Satin
117-2790 High Gloss

Surface Preparation:

Substrate must be sanded using 120 or 150 grit stearated paper prior to staining or coating. Sealers, if used, should be sanded with 240, 280 and 320 grit stearated paper prior to being coated. The substrate as well as the sealers should be topcoated within eight hours of being sanded. CHEMLIFE 24 PLUS Tint Base TC cannot be used on metal, old oil or cellulose lacquers. Stain systems used under acid catalyzed systems should be acid stable.

General Information:

Catalyze and reduce the material as recommended. CHEMLIFE 24 PLUS Tint Base TC is applied in one to two coats on all kinds of wood meant for indoor use. Thorough sanding between the coats is a must for good adhesion. The second and subsequent coats must be applied the same day as the previous coat is sanded.
Contact with metal surfaces should be avoided once the CHEMLIFE 24 PLUS Tint Base TC has been catalyzed. To ensure proper sheen, the catalyzed material should be agitated at all times.
This product can be used as a self-sealer. Appropriate sealer is Chemlife 24 Conversion Varnish Sealer 421-6300 or CHEMLIFE 24 PLUS Conversion Varnish Primer 522-2500 or 522-2501. Consult with your coatings supplier for specific recommendations.
CHEMLIFE 24 PLUS Tint Base TC demonstrates excellent resistance to marring, dry heat, moisture, household and office liquids, etc. When this product is used as its own sealer, its special formulation ensures excellent filling and easy sanding properties with superior holdout for subsequent coating. CHEMLIFE 24 PLUS Tint Base TC must be thoroughly stirred, while adding catalyst and reducer in the recommended ratio. Total recommended film build of the Chemlife system should not exceed 4 mils dry.
CHEMLIFE 24 PLUS Tint Base TC must not be polluted with oil and must not be sanded with steel wool between coats.
CHEMLIFE 24 PLUS Tint Base TC must not be used and dried at temperatures below 18°C or relative humidity above 65%. During the curing process, the coating must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finished surface. This may accelerate discoloration.

PDF Name: CA-PIS_117-27XX_CHEMLIFE_24_PLUS_CV_Clear_Tint_Base_TC
Tack Free Time: 15 minutes
Files: CA-PIS_117-27XX_CHEMLIFE_24_PLUS_CV_Clear_Tint_Base_TC.pdf
Dry to Sand : 1 hour
Dry to Stack: Overnight
Tack Free Time: Flash off before entering oven
Dry to Sand: 30 minutes
VOC less exempt g/l: <595
VOC g/l: <595
Dry to Stack: 3 hours
Note: N/A
Note:

N/A

spec_description:

CHEMLIFE 24 PLUS Clear Tint Base TC is a complementary product to the CHEMLIFE 24 PLUS series for use when deep dark colors are desired. This tinting base has excellent color stability and delivers a silky feel and aesthetically pleasing look. Provides excellent sprayability and flow with outstanding vertical hang, hardness and durability. Like the other CHEMLIFE 24 products it has a 24 hour potlife.
Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards.
Recommended: Meets Architectural Woodwork Institute (AWI), System 5 performance standard for chemical and moisture resistance.

spec_uses:

This product is recommended for kitchen cabinets, high build office or residential furniture as well as other interior wood applications.

Suggested Uses: Wood Finish
Mixing Ratio:

10% 873-1251

Pot Life: 24 hours
Application Viscosity:

Zahn #2 signature cup 28-30 seconds

Reducer: 121-8020 or 121-803
Retarder: 800-5328 EEP
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: 3 - 5 miols
Coverage:

488 sq. ft / gal at 1 mil dry and 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 28-30 sec at 25°C

Flash Point: 12°C (53.6° F)
Density (lb/gal): 0.96
Solid (% by weight): 38.62%
Solid (% by volume): 30.45%
Shelf Life (months): 12

CHEMLIFE 24 PLUS Tint Base TC

117-27XX CHEMLIFE® 24 PLUS CV Clear Tint Base TC

Find distributor Trouver un distributeur

spec_description:

CHEMLIFE 24 PLUS Clear Tint Base TC is a complementary product to the CHEMLIFE 24 PLUS series for use when deep dark colors are desired. This tinting base has excellent color stability and delivers a silky feel and aesthetically pleasing look. Provides excellent sprayability and flow with outstanding vertical hang, hardness and durability. Like the other CHEMLIFE 24 products it has a 24 hour potlife.
Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards.
Recommended: Meets Architectural Woodwork Institute (AWI), System 5 performance standard for chemical and moisture resistance.

Read more

CHEMLIFE 24 PLUS Tint Base TC

117-27XX CHEMLIFE® 24 PLUS CV Clear Tint Base TC

spec_description:

CHEMLIFE 24 PLUS Clear Tint Base TC is a complementary product to the CHEMLIFE 24 PLUS series for use when deep dark colors are desired. This tinting base has excellent color stability and delivers a silky feel and aesthetically pleasing look. Provides excellent sprayability and flow with outstanding vertical hang, hardness and durability. Like the other CHEMLIFE 24 products it has a 24 hour potlife.
Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards.
Recommended: Meets Architectural Woodwork Institute (AWI), System 5 performance standard for chemical and moisture resistance.

Read more
Product codeCodes de produit
Product Codes:

117-2705 Flat
117-2720 Low Gloss
117-2735 Satin
117-2790 High Gloss


Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 28-30 sec at 25°C

Flash Point: 12°C (53.6° F)
Density (lb/gal): 0.96
Solid (% by weight): 38.62%
Solid (% by volume): 30.45%
Shelf Life (months): 12

Download product information sheets

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Image

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Need help? Contact our team of wood coating experts.

Contact us