Optiset
131-82XX Optiset® 550 Pre-Cat White Topcoat
Product Codes:

131-8215 15° Low Gloss

131-8225 25° Low Gloss
131-8240 40° Satin
131-8260 60° Semi-Gloss

Surface Preparation:

Wood substrate should be sanded with 120, 150 or 180 grit paper prior to coating. Primers should be sanded with 280/320 grit stearated paper prior to topcoating. When recoating, the previous coat of Optiset 550 or primer must be sanded and the next coat applied within eight hours. Optiset 550 White cannot be used on metal, old oil or cellulose lacquers.

General Information:

Agitate material before use. Always mix Optiset 550 while adding hardener and reducers in the recommended mixing ratios. Optiset 550 must be agitated thoroughly at all times to ensure product consistency and consistent gloss.

Apply at 3-5 mils wet on sanded or primed substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper. Maximum film build of Optiset 550 White should not exceed 4 mils dry. Maximum film build of total coating system must not exceed 4 mils dry. The second and subsequent coats must be applied the same day as the previous coat is sanded.

Contact with metal surfaces should be avoided.

Optiset 550 White must not be polluted with oil, varnish or the like and must not be sanded with steel wool between the coats. Optiset 550 White must not be used and dried at temperatures below 18°C or relative humidity above 65%. During hardening the enamel must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finished surface. This may accelerate discoloration.

Basecoats to use with 131-82XX: 522-1624, 545-8016, 546-7257 or self-seal

PDF Name: CA-PIS_131-82XX_Optiset_550_Pre-Cat_White_Topcoat
Tack Free Time: 10 – 15 minutes
Files: CA-PIS_131-82XX_Optiset_550_Pre-Cat_White_Topcoat.pdf
Dry to Sand : 2 hours
Dry to Stack: 3 hours
Tack Free Time: Flash off before entering oven
Dry to Sand: 30 - 45 minutes
VOC less exempt g/l: <550
VOC g/l: <451
Dry to Stack: 60 - 90 minutes
Note: N/A
Note:

See individual compliance sheets for specific data

spec_description:

Optiset 550 is a one-component, pigmented Pre-Catalyzed Reactive Amino Coating (RAC) with good resistance properties. This product meets the German “E-1” classification for the emission of formaldehyde as tested by an accredited laboratory using North American test methods. This is a fast building pigmented pre-catalyzed RAC due to its high solid content (32% volume). Optiset 550 demonstrates very good moisture, household wear, household chemical and mar resistance. The coating has light stable properties due to the type of resin used. This coating may be catalyzed to further enhance its durability. Contact your coating supplier for a recommendation. Optiset 550 has very low odor during the curing process while maintaining its rapid dry and cure properties.

Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards. Recommended: Architectural Woodwork Institute (AWI). O.P.2.

spec_uses:

Optiset 550 is recommended for kitchen cabinets, office and household furniture, as well as other interior wood applications.

Suggested Uses: Spray
Mixing Ratio:

100 parts 131-82XX to 3 parts 999-017*

Pot Life: 8 hours*
Application Viscosity:

Zahn #2 signature cup 35 – 36 seconds

Reducer: 121-803 or 121-8020
Retarder: 800-5328 EEP
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: 3 – 5 mils wet
Coverage:

12 m2/l (130 pi2/l) at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

*Amount of catalyst required & pot life if material is catalyzed.

Viscosity:

Zahn #2 signature cup 36 sec at 77°F (25°C)

Flash Point: -20°C (-4°F)
Density (lb/gal): 1.06
Solid (% by weight): 47%
Solid (% by volume): 31%
Shelf Life (months): 12

Optiset

131-82XX Optiset® 550 Pre-Cat White Topcoat

Find distributor Trouver un distributeur

spec_description:

Optiset 550 is a one-component, pigmented Pre-Catalyzed Reactive Amino Coating (RAC) with good resistance properties. This product meets the German “E-1” classification for the emission of formaldehyde as tested by an accredited laboratory using North American test methods. This is a fast building pigmented pre-catalyzed RAC due to its high solid content (32% volume). Optiset 550 demonstrates very good moisture, household wear, household chemical and mar resistance. The coating has light stable properties due to the type of resin used. This coating may be catalyzed to further enhance its durability. Contact your coating supplier for a recommendation. Optiset 550 has very low odor during the curing process while maintaining its rapid dry and cure properties.

Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards. Recommended: Architectural Woodwork Institute (AWI). O.P.2.

Read more

Optiset

131-82XX Optiset® 550 Pre-Cat White Topcoat

spec_description:

Optiset 550 is a one-component, pigmented Pre-Catalyzed Reactive Amino Coating (RAC) with good resistance properties. This product meets the German “E-1” classification for the emission of formaldehyde as tested by an accredited laboratory using North American test methods. This is a fast building pigmented pre-catalyzed RAC due to its high solid content (32% volume). Optiset 550 demonstrates very good moisture, household wear, household chemical and mar resistance. The coating has light stable properties due to the type of resin used. This coating may be catalyzed to further enhance its durability. Contact your coating supplier for a recommendation. Optiset 550 has very low odor during the curing process while maintaining its rapid dry and cure properties.

Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards. Recommended: Architectural Woodwork Institute (AWI). O.P.2.

Read more
Product codeCodes de produit
Product Codes:

131-8215 15° Low Gloss

131-8225 25° Low Gloss
131-8240 40° Satin
131-8260 60° Semi-Gloss


Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 36 sec at 77°F (25°C)

Flash Point: -20°C (-4°F)
Density (lb/gal): 1.06
Solid (% by weight): 47%
Solid (% by volume): 31%
Shelf Life (months): 12

Download product information sheets

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Image

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Need help? Contact our team of wood coating experts.

Contact us