Butyl Cellosolve
800-5742 Butyl Cellosolve (100-119) (013-0500)
Product Codes:

800-5742 Butyl Cellosolve

Surface Preparation:

N/A

General Information:

N/A

PDF Name: CA-PIS_800-5742_Butyl_Cellosolve_(100-119)_(013-0500)
Tack Free Time: N/A
Dry to Sand : N/A
Dry to Stack: N/A
Tack Free Time: N/A
Dry to Sand: N/A
VOC less exempt g/l: 900
VOC g/l: 900
Dry to Stack: N/A
Note: N/A
Note:

See individual compliance sheets for specific data.

spec_description:

Butyl Cellosolve is a glycol ether with a very slow evaporation rate. Butyl Cellosolve is also referred to as Glycol Ether EB or 2-Butoxyethanol.


spec_uses:

Retarder solvent for nitrocellulose containing coatings used when severe blushing due to extreme humidity is experienced.  As this solvent significantly slows the drying time, it is recommended to start with an addition of 1% of the solvent and not exceed 3%. If the blushing problem persists, contact your AkzoNobel representative.

Suggested Uses: N/A
Mixing Ratio:

 1 - 3% maximum

Pot Life: N/A
Application Viscosity:

N/A

Reducer: N/A
Retarder: N/A
Clean-up Solvent: N/A
Recommended Wet Film: N/A
Coverage:

N/A

Note application:

N/A

Viscosity:

N/A

Flash Point: 65°C
Density (lb/gal): 0.90 ± 2% at 25°C
Solid (% by weight): 0%
Solid (% by volume): 0%
Shelf Life (months): Unlimited

Butyl Cellosolve

800-5742 Butyl Cellosolve (100-119) (013-0500)

Find distributor Trouver un distributeur

spec_description:

Butyl Cellosolve is a glycol ether with a very slow evaporation rate. Butyl Cellosolve is also referred to as Glycol Ether EB or 2-Butoxyethanol.


Read more

Butyl Cellosolve

800-5742 Butyl Cellosolve (100-119) (013-0500)

spec_description:

Butyl Cellosolve is a glycol ether with a very slow evaporation rate. Butyl Cellosolve is also referred to as Glycol Ether EB or 2-Butoxyethanol.


Read more
Product codeCodes de produit
Product Codes:

800-5742 Butyl Cellosolve


Product information

Product specificationsSpécifications du produit

Viscosity:

N/A

Flash Point: 65°C
Density (lb/gal): 0.90 ± 2% at 25°C
Solid (% by weight): 0%
Solid (% by volume): 0%
Shelf Life (months): Unlimited

Download product information sheets

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Image

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Need help? Contact our team of wood coating experts.

Contact us