Peelcoat White

371-1700 Peelcoat White

Product Codes:

371-1700 Peelcoat White

Surface Preparation:

Free of all dust and contaminates.

General Information:

Peelcoat is very thixotropic and will need to be stirred very well in order to break up the false body and make the viscosity spray ready. Failure to mix properly may result in lumps/bumps in the finish or require the use of excess thinners, thereby reducing the peeling properties of the dried coating.

Apply 1 to 3 coats of 5 to 8 mils wet to obtain an appropriate thickness.

PDF Name: CA-PIS_371-1700_Peelcoat_White

Tack Free Time: 15 - 20 minutes

Files: CA-PIS_371-1700_Peelcoat_White.pdf

Dry to Sand : N/A

Dry to Stack: 1 hour

Tack Free Time: N/A

Dry to Sand: N/A

VOC less exempt g/l: 675

VOC g/l: 548

Dry to Stack: N/A

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

This is used as a strippable coating system for surfaces where temporary protection is required. It can easily be removed from the surface by pulling the film of the surface in a coherent foil.

spec_uses:

Peelcoat is primarily used for spray booth coating, but can be used on non-porous substrates where a strippable finish is required.

Suggested Uses: Spray

Mixing Ratio:

N/A

Pot Life: N/A

Application Viscosity:

As required

Reducer: Lacquer Thinner if needed

Retarder: N/A

Clean-up Solvent: Lacquer Thinner

Recommended Wet Film: 5 - 8 mils wet

Coverage:

N/A

Note application:

N/A

Viscosity:

28 sec ± 2 Zahn #2 at 25°C

Flash Point: -20°C

Density (lb/gal): 0.95 ± 2% at 25°C

Solid (% by weight): 27%

Solid (% by volume): 16%

Shelf Life (months): 6

Peelcoat White

371-1700 Peelcoat White

Find distributor Trouver un distributeur

spec_description:

This is used as a strippable coating system for surfaces where temporary protection is required. It can easily be removed from the surface by pulling the film of the surface in a coherent foil.

BACK

Peelcoat White

371-1700 Peelcoat White

spec_description:

This is used as a strippable coating system for surfaces where temporary protection is required. It can easily be removed from the surface by pulling the film of the surface in a coherent foil.

Product codeCodes de produit
Product Codes:

371-1700 Peelcoat White

Product information

Product specificationsSpécifications du produit

Viscosity:

28 sec ± 2 Zahn #2 at 25°C

Flash Point: -20°C

Density (lb/gal): 0.95 ± 2% at 25°C

Solid (% by weight): 27%

Solid (% by volume): 16%

Shelf Life (months): 6

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_371-1700_Peelcoat_White.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap