Danspeed
482-3XX Danspeed® Extra Light Post-Cat Clear Topcoat
Product Codes:

482-310  10° Matte

482-325  25° Low Gloss

482-335  35° Satin

482-345  45° Semi-Gloss

Surface Preparation:

Wood substrate should be sanded with 120, 150 or 180 grit paper prior to staining or coating. Sealers should be sanded with 280/320 grit stearated paper prior to topcoating. When recoating, the sealer or previous coat must be sanded and the next coat applied within eight hours. Stain systems under acid containing coatings should be acid stable. Danspeed Extra Light can not be used on metal, old oil or cellulose lacquers.

General Information:

Agitate material before use. Always mix Danspeed Extra Light while adding hardener and reducers in the recommended mixing ratios. Danspeed Extra Light must be agitated thoroughly at all times to ensure product consistency and consistent gloss.
Apply at 3-5 mils wet on sanded substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper.
Contact with metal surfaces should be avoided.
Maximum film build of Danspeed Extra Light should not exceed 4 mils dry. Maximum film build of total coating system must not exceed 4 mils dry.

To obtain a complete cure, the system should be applied at an ambient temperature above 18ºC and a relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surfaces must not be cleaned with ammonia containing products.

482-3XX can be used as a self-seal or with following sealers: 390-001, 390-0060, 401-004 catalyzed, 401-028 catalyzed, 432-1220, 546-5192 and 546-8003.

PDF Name: CA-PIS_482-3XX_Danspeed_Extra_Light_Post-Cat_Clear_Topcoat
Tack Free Time: 15 minutes
Files: CA-PIS_482-3XX_Danspeed_Extra_Light_Post-Cat_Clear_Topcoat.pdf
Dry to Sand : 60 - 90 minutes
Dry to Stack: 12 hours
Tack Free Time: Flash off before entering oven
test: 45 - 60 minutes
VOC less exempt g/l: 575
VOC g/l: 575
Dry to Stack: 2 hours
Note: N/A
Note:

See individual compliance sheets for specific data

spec_description:

Danspeed Extra Light is a two component, high solids reactive amino coating. It provides a smooth, hard wearing surface that is resistant to alcohol, water, grease and usual household chemicals. Danspeed Extra Light has improved yellowing resistance when compared to Danspeed Extra.

spec_uses:

Danspeed Extra Light is designed for all types of wood for interior use.

Suggested Uses: Spray
Mixing Ratio:

10:1 with 999-017 or 999-031A by volume

Pot Life:

8 hours

Application Viscosity:

Zahn #2 signature cup 20-25 seconds

Reducer: 121-8020 or 121-803
Retarder: 800-5742 or 800-5328
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: 3-5 wet mils
Coverage:

13 m2/l at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 42 sec at 25°C

Flash Point: 12°C (57°F)
Density (lb/gal): 0.96
Solid (% by weight): 40%
Solid (% by volume): 33%
Shelf Life (months): 12

Danspeed

482-3XX Danspeed® Extra Light Post-Cat Clear Topcoat

Find distributor Trouver un distributeur

spec_description:

Danspeed Extra Light is a two component, high solids reactive amino coating. It provides a smooth, hard wearing surface that is resistant to alcohol, water, grease and usual household chemicals. Danspeed Extra Light has improved yellowing resistance when compared to Danspeed Extra.

Read more

Danspeed

482-3XX Danspeed® Extra Light Post-Cat Clear Topcoat

spec_description:

Danspeed Extra Light is a two component, high solids reactive amino coating. It provides a smooth, hard wearing surface that is resistant to alcohol, water, grease and usual household chemicals. Danspeed Extra Light has improved yellowing resistance when compared to Danspeed Extra.

Read more
Product codeCodes de produit
Product Codes:

482-310  10° Matte

482-325  25° Low Gloss

482-335  35° Satin

482-345  45° Semi-Gloss


Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 42 sec at 25°C

Flash Point: 12°C (57°F)
Density (lb/gal): 0.96
Solid (% by weight): 40%
Solid (% by volume): 33%
Shelf Life (months): 12

Download product information sheets

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Image

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Need help? Contact our team of wood coating experts.

Contact us