E.S. Sealer

390-001 ES Sealer II Pre-Cat Clear Sealer

Product Codes:

390-001 E.S. Sealer II

(390-0010)

Surface Preparation:

Wood must be sanded with a 120, 150 or 180 grit paper and free of dust and all contaminants prior to staining or coating. Sealer must be sanded with a 280/320 paper and the next coat applied within 8 hours of being sanded. This sealer must not be applied over metal, old finish or nitrocellulose lacquer. Stain systems used under acid catalyzed systems should be acid stable.

General Information:

Agitate material before use. This product must be agitated thoroughly at all times to ensure consistency. Apply 3 to 5 mils wet on sanded surface. Further coats can be applied after complete drying of the first coat. A thorough sanding of each coat with paper # 280/320 is essential for proper adhesion. Eliminate all contact with metallic surfaces. Maximum film build of the topcoat should not exceed 2 mils dry. Maximum film build of the system should not exceed 4 mils dry.

To obtain complete cure, E.S. Sealer should be applied at a temperature above 18°C and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surfaces must not be cleaned with ammonia containing products. Always use plastic or stainless equipment to eliminate discoloration due to oxidation.

Topcoats to use with 390-001: 431-22XX, 431-90XX, 431-98XX, 421-55XX, 421-67XX, 421-72XX and 482-3XX

PDF Name: CA-PIS_390-001_ES_Sealer_II_Pre-Cat_Clear_Sealer

Tack Free Time: 10 - 15 minutes

Files: CA-PIS_390-001_ES_Sealer_II_Pre-Cat_Clear_Sealer.pdf

Dry to Sand : 30 - 45 minutes

Dry to Stack: 2 hours

Tack Free Time: Flash off before entering oven

test: 15 - 20 minutes

VOC less exempt g/l: 727

VOC g/l: 727

Dry to Stack: 30 minutes

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

E.S. Sealer is a one-component Pre-Catalyzed Reactive Amino Coating (RAC) sealer. It has a rapid dry and sands easily to a smooth finish.

spec_uses:

E.S. Sealer is use for an open or semi open grain finish on all type of wood for interior use.

Suggested Uses:

Spray

Mixing Ratio:

3% 999-017 if catalyzed

Pot Life: 8 hours if catalyzed

Application Viscosity:

18-22 sec Zahn #2 at 25°C

Reducer: Lacquer thinner 121-001/803-1339 or 121-8020

Retarder: 800-5328 EEP

Clean-up Solvent: Lacquer Thinner

Recommended Wet Film: 3 to 5 wet mils

Coverage:

6 m²/l (60 pi²/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 22 sec at 25°C

Flash Point: 7°C

Density (lb/gal): 0.93 ± 2% at 25°C

Solid (% by weight): 22 ± 2%

Solid (% by volume): 15 ± 2%

Shelf Life (months): 6

E.S. Sealer

390-001 ES Sealer II Pre-Cat Clear Sealer

Find distributor Trouver un distributeur

spec_description:

E.S. Sealer is a one-component Pre-Catalyzed Reactive Amino Coating (RAC) sealer. It has a rapid dry and sands easily to a smooth finish.

BACK

E.S. Sealer

390-001 ES Sealer II Pre-Cat Clear Sealer

spec_description:

E.S. Sealer is a one-component Pre-Catalyzed Reactive Amino Coating (RAC) sealer. It has a rapid dry and sands easily to a smooth finish.

Product codeCodes de produit
Product Codes:

390-001 E.S. Sealer II

(390-0010)

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 22 sec at 25°C

Flash Point: 7°C

Density (lb/gal): 0.93 ± 2% at 25°C

Solid (% by weight): 22 ± 2%

Solid (% by volume): 15 ± 2%

Shelf Life (months): 6

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_390-001_ES_Sealer_II_Pre-Cat_Clear_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap