E.S. HS Sealer

431-1219 E.S. HS Sealer

Product Codes:

431-1219 E.S. HS Sealer

Surface Preparation:

Wood must be sanded with a #120, 150 or 180 grit paper and free of dust and all contaminants. Sealer must be sanded with a #280/320 paper and the topcoat must be applied within 8 hours after the sanding. Stain systems under acid containing coatings should be acid stable.

General Information:

Apply 1 or 2 coats of 3 to 5 mils wet and allow 30‑45 minutes dry at 20°C prior to sanding and applying next coating. A thorough sanding with 280/320 grit paper of each coat is essential for proper adhesion. Eliminate all contact with metallic surfaces. Maximum film build of the topcoat should not exceed 2 mils dry. Maximum film build of the system should not exceed 4 mils dry.

431-1219 is used under pre-catalyzed following topcoat: 431-90XX and 431-98XX (355-8XX).

To obtain complete cure, E.S. HS Sealer should be applied at a temperature above 18°C and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapours. Finished surfaces must not be cleaned with ammonia containing products. Always use plastic or stainless equipment to eliminate discoloration due to oxidation.

PDF Name: CA-PIS_431-1219_E.S._HS_Sealer

Tack Free Time: 15 - 20 minutes

Files: CA-PIS_431-1219_E.S._HS_Sealer.pdf

Dry to Sand : 45 - 60 minutes

Dry to Stack: 2 - 3 hours

Tack Free Time: Flash off before entering oven

test: 15 - 20 minutes

VOC less exempt g/l: 672

VOC g/l: 672

Dry to Stack: 20 – 30 minutes

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

E.S. HS Sealer is a one-component, pre-catalyzed sealer designed for all types for all types of woods for interior use. It is rapid dry and sands easily to a smooth finish. This particular product is developed to have higher solids than our standard E.S. Sealer while maintaining the same ease of use.

spec_uses:

Used as a protective coating for wood. For interior uses only.

Suggested Uses: Spray

Mixing Ratio:

N/A

Pot Life: N/A

Application Viscosity:

18-24 sec Zahn #2 at 25°C

Reducer: Lacquer Thinner

Retarder: N/A

Clean-up Solvent: Lacquer Thinner

Recommended Wet Film: 3 - 5 wet mils

Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #2 signature cup 22 sec at 25°C

Flash Point: -3°C (26°F)

Density (lb/gal): 0.94 ± 2% at 25°C

Solid (% by weight): 28%

Solid (% by volume): 20%

Shelf Life (months): 6

E.S. HS Sealer

431-1219 E.S. HS Sealer

Find distributor Trouver un distributeur

spec_description:

BACK

E.S. HS Sealer

431-1219 E.S. HS Sealer

spec_description:

Product codeCodes de produit
Product Codes:

431-1219 E.S. HS Sealer

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 22 sec at 25°C

Flash Point: -3°C (26°F)

Density (lb/gal): 0.94 ± 2% at 25°C

Solid (% by weight): 28%

Solid (% by volume): 20%

Shelf Life (months): 6

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_431-1219_E.S._HS_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap