Catlac

431-30XX Catlac Pre-Cat Low VOC Clear Topcoat

Product Codes:

431-3010 10° Matte

431-3025 25° Low Gloss

431-3035 35° Satin

431-3050 50° Semi-Gloss

431-3090 90° High Gloss

Surface Preparation:

Sealer must be sanded with a #280/320 grit stearated paper and free of dust and all contaminants before application of the topcoat. Catlac must not be applied over metal, old finish or nitrocellulose lacquer. Stain systems used should be acid stable.

General Information:

Agitate material before use. Keep under mixing to ensure product consistency and consistent gloss. Apply at 3- 5 mils on sanded sealer. One extra coat may be applied after complete drying followed by sanding with 280/320 grit stated paper. The subsequent coat must be applied the same day as the previous coat is sanded. Maximum film build of the topcoat should not exceed 2 mils dry. Maximum film build of the system should not exceed 4 mils dry. Eliminate all contact with metallic surfaces. Catlac must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats.

To obtain complete cure, Catlac should be applied at a temperature above 18°C and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapours. Finished surfaces must not be cleaned with ammonia containing products. Always use plastic or stainless equipment to eliminate discoloration due to oxidation.

Sealers to use with 431-30XX: 390-0060, 431-1219, 546-8003 and 546-5192.

PDF Name: CA-PIS_431-30XX_Catlac_Pre-Cat_Low_VOC_Clear_Topcoat

Tack Free Time: 20 - 30 minutes

Files: CA-PIS_431-30XX_Catlac_Pre-Cat_Low_VOC_Clear_Topcoat.pdf

Dry to Sand : 45 - 60 minutes

Dry to Stack: 8 hours

Tack Free Time: Flash off before entering oven

test: 30 - 45 minutes

VOC less exempt g/l: 654

VOC g/l: 578

Dry to Stack: 2 hours

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

Catlac is a one component, ready to use, Pre-Catalyzed Reactive Amino Coating (RAC). This product dries quickly and demonstrates good household wear, household chemical and solvent resistance.

Special Recognition: Meets Kitchen Cabinet Manufacturer Associations (KCMA) Standards.

spec_uses:

Recommended for office and household furniture, kitchen cabinets as well as many other interior wood applications.

Suggested Uses:

Wood Finish / Spray

Mixing Ratio:

N/A

Pot Life: N/A

Application Viscosity:

25 ± 2 sec Zahn #2 at 25°C

Reducer: 5-10% of 121-8020 or 121-803 if necessary

Retarder: 800-5328 EEP

Clean-up Solvent: Lacquer Thinner

Recommended Wet Film: 3 to 5 wet mils

Coverage:

8 m²/l (85 pi²/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 25 sec at 25°C

Flash Point: -4°F (-20°C)

Density (lb/gal): 0.92 ± 2% at 25°C

Solid (% by weight): 27 ± 2%

Solid (% by volume): 20 ± 2%

Shelf Life (months): 6

Catlac

431-30XX Catlac Pre-Cat Low VOC Clear Topcoat

Find distributor Trouver un distributeur

spec_description:

Catlac is a one component, ready to use, Pre-Catalyzed Reactive Amino Coating (RAC). This product dries quickly and demonstrates good household wear, household chemical and solvent resistance.

Special Recognition: Meets Kitchen Cabinet Manufacturer Associations (KCMA) Standards.

BACK

Catlac

431-30XX Catlac Pre-Cat Low VOC Clear Topcoat

spec_description:

Catlac is a one component, ready to use, Pre-Catalyzed Reactive Amino Coating (RAC). This product dries quickly and demonstrates good household wear, household chemical and solvent resistance.

Special Recognition: Meets Kitchen Cabinet Manufacturer Associations (KCMA) Standards.

Product codeCodes de produit
Product Codes:

431-3010 10° Matte

431-3025 25° Low Gloss

431-3035 35° Satin

431-3050 50° Semi-Gloss

431-3090 90° High Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 25 sec at 25°C

Flash Point: -4°F (-20°C)

Density (lb/gal): 0.92 ± 2% at 25°C

Solid (% by weight): 27 ± 2%

Solid (% by volume): 20 ± 2%

Shelf Life (months): 6

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_431-30XX_Catlac_Pre-Cat_Low_VOC_Clear_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap