Basecoat Blanc

522-1624 Basecoat Blanc LVOC Pre-Cat Pigmented Basecoat

Product Codes:

522-1624

Surface Preparation:

Substrate must be sanded with 120, 150 or 180 grit paper, free of dust and other contaminants. Before the application of the topcoat, the Basecoat must be sanded with a 280/320 grit paper. The Basecoat must be recovered within 8 hours after the sanding. This product must not be applied over metal, old finish or nitrocellulose lacquer.

General Information:

Agitate material before use. Always mix while adding reducers in the recommended mixing ratio. The Basecoat can be applied in one or two layers. A good sanding between coats with paper 240/320 is needed to get a good adhesion. The Basecoat must be recovered within 8 hours after the sanding. When sanding, it is important not to wear through the surface and to pay particular attention to sharp edges of the profile. This can create a non-uniform thickness of the application. Avoid all contact with metallic surface. The dry film thickness of the Basecoat must not exceed 2 mils. The total dry film thickness of the system should not exceed 4 mils.

To obtain a complete cure, the system should be applied at an ambient temperature above 18°C and a relative humidity below 65%. During curing, this product should not be exposed to ammonia vapors. The finished surface cannot be cleaned with an ammonia-based product. Contact with metal surface should be avoided. Always use containers and equipment in plastic or stainless steel to eliminate any source of discoloration due to oxidation.

Topcoats to use over 522-1624: 131-50XX, 131-51XX, 131-82XX, 117-30XX, 117-32XX, 440-XXX and 484-6XX.

PDF Name: CA-PIS_522-1624_Basecoat_Blanc_LVOC_Pre-Cat_Pigmented_Basecoat

Tack Free Time: 30 - 45 minutes

Files: CA-PIS_522-1624_Basecoat_Blanc_LVOC_Pre-Cat_Pigmented_Basecoat.pdf

Dry to Sand : 45 - 60 minutes

Dry to Stack: 2 - 4 hours

Tack Free Time: Flash off before entering oven

Dry to Sand: 30 - 45 minutes

VOC less exempt g/l: 569

VOC g/l: 505

Dry to Stack: 60 - 90 minutes

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

Low VOC, one component Pre-Catalyzed Reactive Amino Coating (RAC) basecoat. This pigmented primer provides superior built due to the high solids.

spec_uses:

Used as a protective coatings for wood for interior usage. It has good filling properties and hiding characteristics.

Suggested Uses:

Spray

Mixing Ratio:

N/A

Pot Life: N/A

Application Viscosity:

22-30 sec Zahn #2 at 25°C

Reducer: Lacquer Thinner 121-001 / 803-1339 or 121-8020 if required

Retarder: 800-5328 EEP

Clean-up Solvent: Lacquer Thinner

Recommended Wet Film: 3 to 5 mils wet

Coverage:

11 m²/l ( 115 pi²/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 36 sec at 25°C

Flash Point: -20°C

Density (lb/gal): 1.2 ± 2% at 25°C

Solid (% by weight): 50% ± 1%

Solid (% by volume): 27% ± 1%

Shelf Life (months): 12

Basecoat Blanc

522-1624 Basecoat Blanc LVOC Pre-Cat Pigmented Basecoat

Find distributor Trouver un distributeur

spec_description:

Low VOC, one component Pre-Catalyzed Reactive Amino Coating (RAC) basecoat. This pigmented primer provides superior built due to the high solids.

BACK

Basecoat Blanc

522-1624 Basecoat Blanc LVOC Pre-Cat Pigmented Basecoat

spec_description:

Low VOC, one component Pre-Catalyzed Reactive Amino Coating (RAC) basecoat. This pigmented primer provides superior built due to the high solids.

Product codeCodes de produit
Product Codes:

522-1624

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 36 sec at 25°C

Flash Point: -20°C

Density (lb/gal): 1.2 ± 2% at 25°C

Solid (% by weight): 50% ± 1%

Solid (% by volume): 27% ± 1%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_522-1624_Basecoat_Blanc_LVOC_Pre-Cat_Pigmented_Basecoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap