Acquaduro

550-1601 Acquaduro™ 1K Waterborne Neutral Primer

Product Codes:

550-1601

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit paper prior to coating.

Acquaduro™ 1K Waterborne
Neutral Primer should be sanded with 280/320 grit paper prior to being coated.

Acquaduro™ 1K Waterborne Neutral Primer should be coated within (8) hours of being sanded for maximum adhesion.

General Information:

Mix material before use. Add water to reduce if required and mix thoroughly. Apply by spray at 4 - 6 mils wet. Acquaduro™ 1K
Waterborne Neutral Primer must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces
should be avoided. Maximum film build of total coating system must not exceed 4 mils dry.
THE CUSTOMER IS RESPONSIBLE FOR FOLLOWING THE RECOMMENDED APPLICATION PROCEDURES. FAILURE TO ADHERE TO THE
RECOMMENDATIONS GIVEN IN THIS DATA SHEET WILL LIKELY RESULT IN UNSATISFACTORY FILM APPEARANCE OR FILM FAILURE. THE
COMPLETE COATING SYSTEM SHOULD BE CHECKED FOR REQUIRED PROPERTIES PRIOR TO THE START-UP OF PRODUCTION.

PDF Name: CA-PIS_550-1601_Acquaduro_1K_Waterborne_Neutral_Primer

Tack Free Time: 10 minutes

Files: CA-PIS_550-1601_Acquaduro_1K_Waterborne_Neutral_Primer.pdf

Dry to Sand : 20 minutes

Dry to Stack: 12 hours

Tack Free Time: 5 minutes

Dry to Sand: 10 minutes

VOC less exempt g/l: 48.0

VOC g/l: 19.0

Dry to Stack: 30 minutes

Note: N/A

Note:

N/A

spec_description:

Acquaduro™ 1K Neutral Primer is a ready to use neutral waterborne primer. This waterborne primer provides excellent durability and water resistance on hardwoods or MDF. Acquaduro Waterborne Primer has great ease of application and fast application and dry times.
Recommended topcoat is the Acquaduro 2K Pigmented or Neutral Polyurethane Waterborne Topcoat.

spec_uses:

Acquaduro™ 1K Waterborne Neutral Primer has been designed for the cabinet, architectural millwork, furniture and refinish
markets.

Suggested Uses: Designed for use on hardwoods or MDF

Mixing Ratio:

N/A

Pot Life: N/A

Application Viscosity:

Zahn #2 Signature cup 30-35 sec at 25º C

Reducer: Use water if required

Retarder: 970-1358 1 to 3 % by Volume

Clean-up Solvent: Water

Recommended Wet Film: 4-6 wet mils

Coverage:

610 sqft/gal

Note application:

N/A

Viscosity:

Zahn #2 Signature Cup 30-35 seconds at 25ºC

Flash Point: >93.3°C (200°F)

Density (lb/gal): 11.31

Solid (% by weight): 56.4

Solid (% by volume): 40.7

Shelf Life (months): 12

Acquaduro

550-1601 Acquaduro™ 1K Waterborne Neutral Primer

Find distributor Trouver un distributeur

spec_description:

BACK

Acquaduro

550-1601 Acquaduro™ 1K Waterborne Neutral Primer

spec_description:

Product codeCodes de produit
Product Codes:

550-1601

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 Signature Cup 30-35 seconds at 25ºC

Flash Point: >93.3°C (200°F)

Density (lb/gal): 11.31

Solid (% by weight): 56.4

Solid (% by volume): 40.7

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_550-1601_Acquaduro_1K_Waterborne_Neutral_Primer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap