Plasticolor enamel must be thoroughly stirred, while adding hardener and reducers in the recommended ration.  To ensure proper sheen, the catalyzed material should be agitated at all times. Apply 3 - 5 mils wet on sanded surface. A subsequent coat can be applied after complete cure, and a good sanding with #280/320 grit paper is necessary to obtain a good adhesion.  The subsequent coat must be applied the same day as the previous coat is sanded. Dry film thickness of topcoat must not exceed 3 mils.  Total dry film thickness of system should not exceed 6 mils. Plasticolor must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats. Contact with metal surfaces should be avoided once the Plasticolor White RTS has been catalyzed. 
To obtain complete cure, the Plasticolor must be applied at a temperature above 18ºC and relative humidity below 65%.  When drying, this product is not to be exposed to ammonia vapors. Finished surface must not be cleaned with ammonia containing products. 

Primers to use with 117-55XX Plasticolor White RTS Conversion Varnish Pigmented Topcoat are:
220-214 Plastiprimer Off White Post-Cat Pigmented Primer
522-1410 Plastiprimer 900 White Post-Cat Pigmented Primer

Catalyze and reduce the material as recommended. CHEMLIFE 24 PLUS White Topcoat is applied in one or two coats and can be used on all kinds of wood meant for interior use.

A thorough sanding between the coats is essential to the adhesion. The second and subsequent coats must be applied the same day as the previous coat is sanded. CHEMLIFE 24 PLUS White Topcoat cannot be used on metal, old oil or cellulose lacquers.

Total recommended film build of CHEMLIFE 24 PLUS White Primer 522-2500 and CHEMLIFE 24 PLUS White Topcoat 117-25XX is not to exceed 6 mils dry. Over the primer, the topcoat should not exceed 4 mils dry.

To ensure proper sheen, the catalyzed material should be agitated at all times. Chemlife 24 Plus White must be thoroughly stirred while adding catalyst and thinner in the recommended mixing ratio. Contact with metal surfaces should be avoided once the Chemlife 24 Plus White has been catalyzed.

CHEMLIFE 24 PLUS White Topcoat must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats. CHEMLIFE 24 PLUS White Topcoat must not be used and dried at temperatures below 65°F (18°C) or relative humidity above 65%. During the curing process, the coating must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finished surface. This may accelerate discoloration.

Mix well before and during the addition of catalyst and diluents. To assure consistency, always keep the product under agitation. The Plastiprimer can be applied in one or two coats. A good sanding between coats with paper # 240/320 is needed to get a good adhesion. The Plastiprimer must be covered within 8 hours after the sanding. When sanding, it is important not to wear through the surface and to pay particular attention to sharp edges of the profile. This can create a non-uniform thickness of the application. Once catalyzed, avoid all contact with metallic surface. The dry film thickness of the Plastiprimer must not exceed 3 mils. The total dry film thickness of the system should not exceed 6 mils. 

To obtain a complete cure, the system should be applied at an ambient temperature above 18°C and a relative humidity below 65%. During curing, this product should not be exposed to ammonia vapors. The finished surface cannot be cleaned with an ammonia-based product. Always use containers and equipment in plastic or stainless steel to eliminate any source of discoloration due to oxidation.

The Plastiprimer is used under following topcoats: 117-32XX, 440-XXX

Mix CHEMLIFE 24 PLUS White Primer thoroughly, then catalyze and reduce material as recommended. CHEMLIFE 24 PLUS White Primer must be well mixed while adding catalyst and reducers and must be agitated at all times to ensure product consistency.

CHEMLIFE 24 PLUS White Primer is applied in one or two coats and can be used as a primer for most wood and wood products meant for indoor use. A thorough sanding using 240/320 grit stearated paper between coats is essential for adhesion. The second and subsequent coats must be applied the same day as the previous coat is sanded. Care should be taken to avoid sanding through the primer coat. With profiled edges, care must be taken with sanding of primer to avoid sanding through sharp edges. Complex profiles or profiles with sharp corners may cause difficulties in obtaining an effective primer coat of even thickness. In these cases, profile design must be discussed with your technical representative. Contact with metal surfaces should be avoided once the CHEMLIFE 24 PLUS White Primer has been catalyzed. To ensure proper uniformity, the material should be agitated at all times. Recommended film build of CHEMLIFE 24 PLUS White Primer is not to exceed 4 mils dry. Total recommended film build of CHEMLIFE 24 PLUS White Primer and CHEMLIFE 24 PLUS White is not to exceed 6 mils dry.

CHEMLIFE 24 PLUS White Primer must not be polluted with oil, varnish or the like and must not be sanded with steel wool between the coats. CHEMLIFE 24 PLUS White Primer must not be used and dried at temperatures below 18°C or relative humidity above 65%. During the curing process, the coating must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finish surfaces. This may accelerate discoloration.