Promatch®
824-3602 Promatch® Waterborne Wipe Stain Base
Product Codes:
824-3602 Wipe Stain Base
Surface Preparation:
The substrate must be sanded with a 180 grit sand paper and free of dust and all contaminants.
General Information:
Please refer to your technical sales representative for tinting recommendations. Overshooting dyes and tints can cause adhesion failure. It is to the user responsibility to validate performance.
Apply a generous layer of the wipe stain, wait 30 seconds to 1 minute to start wiping off the stain using a clean rag. It is important to process quickly. Once the work done, a 4 hours waiting period at room temperature should be respected before the application of the water-based sealer.
To obtain expected results, Promatch® Waterborne W/S Base should be applied at a temperature above 18°C and relative humidity below 65%.
See SDS - Keep from freezing. Contact with metallic surfaces must be avoided. It is important to recoat the stain within 8 hours of its application.
PDF Name: CA-PIS_824-3602_Promatch_Waterborne_Wipe_Stain_Base
Tack Free Time: N/A
Files: CA-PIS_824-3602_Promatch_Waterborne_Wipe_Stain_Base.pdf
Dry to Sand : N/A
Dry to Stack: N/A
Tack Free Time: N/A
Dry to Sand: N/A
VOC less exempt g/l: 900
VOC g/l: 360
Dry to Stack: N/A
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Waterborne Wipe Stain base providing an easy of wipe and a remarkable wetting power.
spec_uses:
Developed for all solid and veneer wood substrate.
For interior use only.
Suggested Uses: Spray / Wipe
Mixing Ratio:
N/A
Pot Life: N/A
Application Viscosity:
N/A
Reducer: Water if needed
Retarder: 013-0500 @ 2-5%
Clean-up Solvent: Water, 800-5742, Clean wipe with a rag
Recommended Wet Film: N/A
Coverage:
N/A
Note application:
N/A
Viscosity:
180-220 cps at 25°C
Flash Point: N/A
Density (lb/gal): 1.01 ± 2% at 25°C
Solid (% by weight): 5 ± 0.5%
Solid (% by volume): 4 ± 0.5%
Shelf Life (months): 6

Promatch®

824-3602 Promatch® Waterborne Wipe Stain Base

Find distributor Trouver un distributeur

spec_description:

Waterborne Wipe Stain base providing an easy of wipe and a remarkable wetting power.

BACKRetour

Product codeCodes de produit
Product Codes:

824-3602 Wipe Stain Base

Product information

Product specificationsSpécifications du produit

Viscosity:
180-220 cps at 25°C
Flash Point: N/A
Density (lb/gal): 1.01 ± 2% at 25°C
Solid (% by weight): 5 ± 0.5%
Solid (% by volume): 4 ± 0.5%
Shelf Life (months): 6

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_824-3602_Promatch_Waterborne_Wipe_Stain_Base.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more