Lustrate
436-2104 Lustrate PU Clear Sealer
Product Codes:
436-2104
Surface Preparation:
Substrate should be sanded with 120, 150 or 180 grit sandpaper prior to finishing. Difficult or oily substrates may require the use of 401-033 Isolante Sealer prior to priming to ensure maximum adhesion.
General Information:
Prepare material as per hardener mixing ratio and apply over desired surface at 3-5 mils wet.
Mixed product will contain 999-067, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials. The relative humidity in the application and drying rooms should never exceed 75%.
After drying, scuff sand with 280-320 grit paper and topcoat within eight hours. If left over eight hours, the sealer should be re-sanded prior to topcoating.
Total dry film build of the system including topcoat is not to exceed 6 dry mils.
Topcoats to use over 436-2104: Chemlite 436-31XX or Lustrate 436-1399.
PDF Name: CA-PIS_436-2104_Lustrate_PU_Clear_Sealer
Tack Free Time: 10 - 15 minutes
Files: CA-PIS_436-2104_Lustrate_PU_Clear_Sealer.pdf
Dry to Sand : 20 - 30 minutes
Dry to Stack: Overnight
Tack Free Time: 3 - 5 minutes
Dry to Sand: 10 - 15 minutes
VOC less exempt g/l: 692
VOC g/l: 692
Dry to Stack: 2 - 4 hours
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Lustrate Sealer is designed to provide the improved adhesion characteristics typical of a urethane material. When topcoated with Chemlite or Lustrate, the system provides exceptional durability and light stability.
spec_uses:
436-2104 is suitable for sealing all types of wood and wood veneers for interior use. The product provides very good water resistance and offers protection from tannin bleed.
Suggested Uses: Spray
Mixing Ratio:
10:1 (10%) with 999-067 (other hardeners possible)
Pot Life:
2-3 hours
Application Viscosity:
Zahn #2 signature cup 20-25 seconds
Reducer: 100-120, 800-5301 or 121-834
Retarder: 800-5328 EEP
Clean-up Solvent: Lacquer Thinner (do not mix with product)
Recommended Wet Film: 3-5 wet mils
Coverage:
N/A
Note application:
N/A
Viscosity:
Zahn #2 signature cup 20 sec at 25°C
Flash Point: -1°C (30°F)
Density (lb/gal): 0.94
Solid (% by weight): 27%
Solid (% by volume): 21%
Shelf Life (months): 12

Lustrate

436-2104 Lustrate PU Clear Sealer

Find distributor Trouver un distributeur

spec_description:

Lustrate Sealer is designed to provide the improved adhesion characteristics typical of a urethane material. When topcoated with Chemlite or Lustrate, the system provides exceptional durability and light stability.

BACKRetour

Product codeCodes de produit
Product Codes:

436-2104

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 20 sec at 25°C
Flash Point: -1°C (30°F)
Density (lb/gal): 0.94
Solid (% by weight): 27%
Solid (% by volume): 21%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_436-2104_Lustrate_PU_Clear_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more