Chemlite
436-31XX Chemlite PU Clear Topcoat
Product Codes:
436-3108 10° Matte
436-3125 25° Low Gloss
436-3141 40° Satin
436-3191 90° High Gloss
Surface Preparation:
Topcoats should be well sanded using 240, 280 or 320 grit stearated paper.
General Information:
Mix the desired amount of material and apply 4-5 mils wet. Do not use excess reducer (>10%), this product is relatively low solids and will appear ‘hungry’ if too much thinner is added.
The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the catalyzed material should be monitored regularly to maintain a consistent appearance.
Mixed product will contain 999-067, an isocyanate based co reactant. Please follow all precautions associated with handling and use of these materials.
Total recommended film thickness of Chemlite is not to exceed 6 mils dry.
The sealer for this product is 436-2104.
PDF Name: CA-PIS_436-31XX_Chemlite_PU_Clear_Topcoat
Tack Free Time: 20 - 30 minutes
Files: CA-PIS_436-31XX_Chemlite_PU_Clear_Topcoat.pdf
Dry to Sand : Overnight
Dry to Stack: Overnight
Tack Free Time: Flash off before entering oven
Dry to Sand: 3 hours
VOC less exempt g/l: 715
VOC g/l: 715
Dry to Stack: 8 hours
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Chemlite is a two component polyurethane finish for interior use. The Chemlite system provides exceptional resistance to discolouration and gives a crosslinked finish that is tough and durable. The coating contains UV absorbers to minimize discolouration of light sensitive substrates.
spec_uses:
Chemlite is an excellent choice for finishing fine furniture, cabinetry and all other wood surfaces intended for interior use. Chemlite is also “water-white” meaning it is exceptional over pigmented basecoats where colour is important.
Suggested Uses: Spray
Mixing Ratio:
20% 876-9102 or 999-067 (20% b.v.)
Pot Life:
3 hours
Application Viscosity:
Zahn #2 signature cup 20-25 seconds
Reducer: 121-834 or 800-5301
Retarder: 800-5328 EEP
Clean-up Solvent: Lacquer Thinner (do not mix with product)
Recommended Wet Film: 4-5 wet mils
Coverage:
N/A
Note application:
N/A
Viscosity:
Zahn #2 signature cup 26 sec at 25°C
Flash Point: 24°C (75°F)
Density (lb/gal): 0.95
Solid (% by weight): 25%
Solid (% by volume): 19%
Shelf Life (months): 12

Chemlite

436-31XX Chemlite PU Clear Topcoat

Find distributor Trouver un distributeur

spec_description:

Chemlite is a two component polyurethane finish for interior use. The Chemlite system provides exceptional resistance to discolouration and gives a crosslinked finish that is tough and durable. The coating contains UV absorbers to minimize discolouration of light sensitive substrates.

BACKRetour

Product codeCodes de produit
Product Codes:

436-3108 10° Matte
436-3125 25° Low Gloss
436-3141 40° Satin
436-3191 90° High Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 26 sec at 25°C
Flash Point: 24°C (75°F)
Density (lb/gal): 0.95
Solid (% by weight): 25%
Solid (% by volume): 19%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_436-31XX_Chemlite_PU_Clear_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more