D-Dur
620-1XX D-Dur PU Clear Topcoat
Product Codes:
620-117 Low Gloss
620-106 Satin
620-114 Gloss
Surface Preparation:
Wood substrate should be sanded with 120, 150 or 180 grit prior to staining or coating. Primer should be well sanded using 240, 280 or 320 grit stearated paper.
General Information:
Mix the desired amount of material and apply 3-5 mils wet.
The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the mixed material should be monitored regularly to maintain a consistent appearance.
Mixed product will contain 999-062, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials.
Total recommended film thickness of D-Dur system is not to exceed 6 mils dry.
This product should be used as a self-seal.
PDF Name: CA-PIS_620-1XX_D-Dur_PU_Clear_Topcoat
Tack Free Time: 20 - 30 minutes
Files: CA-PIS_620-1XX_D-Dur_PU_Clear_Topcoat.pdf
Dry to Sand : 6 - 8 hours
Dry to Stack: Overnight
Tack Free Time: 15 - 20 minutes
Dry to Sand: 2 - 3 hours
VOC less exempt g/l: 654
VOC g/l: 654
Dry to Stack: Overnight
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
D-Dur is a two-component polyurethane with very good wetting properties. It provides excellent flexibility and good resistance to weathering.
spec_uses:
This finish is recommended for wooden surfaces where good outdoor durability is desired (i.e., window frames, doors, wooden garden furniture).
Suggested Uses: Spray
Mixing Ratio:
4:1 with 999-062
Pot Life:
3 hours
Application Viscosity:
Zahn #2 signature cup 20-25 seconds
Reducer: 121-834 or 800-5301
Retarder: 800-5328 EEP
Clean-up Solvent: Lacquer Thinner (do not mix with product)
Recommended Wet Film: 3-5 wet mils
Coverage:
N/A
Note application:
N/A
Viscosity:
Zahn #2 signature cup 22 sec at 25°C
Flash Point: 15°C (59°F)
Density (lb/gal): 0.97
Solid (% by weight): 33%
Solid (% by volume): 26%
Shelf Life (months): 12

D-Dur

620-1XX D-Dur PU Clear Topcoat

Find distributor Trouver un distributeur

spec_description:

D-Dur is a two-component polyurethane with very good wetting properties. It provides excellent flexibility and good resistance to weathering.

BACKRetour

Product codeCodes de produit
Product Codes:

620-117 Low Gloss
620-106 Satin
620-114 Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 22 sec at 25°C
Flash Point: 15°C (59°F)
Density (lb/gal): 0.97
Solid (% by weight): 33%
Solid (% by volume): 26%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_620-1XX_D-Dur_PU_Clear_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more