Chemlife
117-24XX Chemlife® 24 White Conversion Varnish Pigmented Topcoat
Product Codes:
117-2410 10° Matte
117-2420 20° Low Gloss
117-2435 35° Satin
117-2450 50° Semi-Gloss
117-2490 90° High Gloss
Surface Preparation:
Primer should be sanded using 240 and 320 grit stearated paper. The primer should be topcoated within eight hours of sanding. Care should be taken during sanding through the primer.
General Information:
Catalyze and reduce the material as recommended. Chemlife 24 White is applied in one or two coats and can be used on all kinds of wood meant for interior use. A thorough sanding between the coats is essential to the adhesion. The second and subsequent coats must be applied the same day as the previous coat is sanded. Chemlife 24 White cannot be used on metal, old oil or cellulose lacquers. Total recommended film build of the system should not exceed 6 mils dry. Over the primer, the topcoat should not exceed 4 mils dry.
To ensure proper sheen, the catalyzed material should be agitated at all times. Chemlife 24 White must be thoroughly stirred while adding catalyst and thinner in the recommended mixing ratio. Contact with metal surfaces should be avoided once the Chemlife 24 White has been catalyzed.
Chemlife 24 White must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats. To obtain complete cure, Chemlife 24 White must be applied at a temperature above 18ºC and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapours. Finished surface must not be cleaned with ammonia containing products.
Primers to use with 117-24XX: Chemlife White primer 522-2400, 220-2250 and 522-1410.
PDF Name: CA-PIS_117-24XX_Chemlife_24_White_Conversion_Varnish_Pigmented_Topcoat
Tack Free Time: 15 – 20 minutes
Files: CA-PIS_117-24XX_Chemlife_24_White_Conversion_Varnish_Pigmented_Topcoat.pdf
Dry to Sand : 3 hours
Dry to Stack: 16 hours
Tack Free Time: Flash off before entering oven
Dry to Sand: 1 hour
VOC less exempt g/l: 449
VOC g/l: 449
Dry to Stack: 3 hours
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Chemlife 24 White is an acid curing, light stable, fast drying Reactive Amino Coating (RAC) with good building properties. It gives a smooth, knock-proof and hardwearing surface resisting influence from alcohol, water, etc. Due to its 24 hours pot-life, Chemlife 24 White provides the customer with minimum waste resulting in lower production costs. It also provides very good light stability based on the type of resin used and superior vertical hang.
Special recognition: when applied as specified, will meet required performance for the ANSI/KCMA A161.1 1990 9.0 Finish Test. Recommended: Architectural Woodwork Institute (AWI) O.P.4
spec_uses:
This product is used as the final coat over wood, plywood, chipboard, etc., meant for interior use. This product is recommended for kitchen cabinets, high build office or residential furniture as well as many other interior wood applications where high build and durability are required.
Suggested Uses:
Wood Finish/Spray
Mixing Ratio:
10% 873-1251
Pot Life:
24 hours
Application Viscosity:
22-25 sec Zahn #2 at 25°C
Reducer: 121-803 or 121-8020 if necessary
Retarder: 800-5328 EEP (2-3% maximum)
Clean-up Solvent: Lacquer thinner
Recommended Wet Film: 3 to 5 wet mils
Coverage:
17-18 m²/l (190 pi²/l) at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #3 signature cup 20 sec at 25°C
Flash Point: 12°C (55°F)
Density (lb/gal): 1.13 ± 2% at 25°C
Solid (% by weight): 60 ± 2%
Solid (% by volume): 45 ± 2%
Shelf Life (months): 12

Chemlife

117-24XX Chemlife® 24 White Conversion Varnish Pigmented Topcoat

Find distributor Trouver un distributeur

spec_description:

Chemlife 24 White is an acid curing, light stable, fast drying Reactive Amino Coating (RAC) with good building properties. It gives a smooth, knock-proof and hardwearing surface resisting influence from alcohol, water, etc. Due to its 24 hours pot-life, Chemlife 24 White provides the customer with minimum waste resulting in lower production costs. It also provides very good light stability based on the type of resin used and superior vertical hang.

Special recognition: when applied as specified, will meet required performance for the ANSI/KCMA A161.1 1990 9.0 Finish Test. Recommended: Architectural Woodwork Institute (AWI) O.P.4

BACKRetour

Product codeCodes de produit
Product Codes:

117-2410 10° Matte
117-2420 20° Low Gloss
117-2435 35° Satin
117-2450 50° Semi-Gloss
117-2490 90° High Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #3 signature cup 20 sec at 25°C
Flash Point: 12°C (55°F)
Density (lb/gal): 1.13 ± 2% at 25°C
Solid (% by weight): 60 ± 2%
Solid (% by volume): 45 ± 2%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_117-24XX_Chemlife_24_White_Conversion_Varnish_Pigmented_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more