Plastofix
421-55XX Plastofix® Light RTS Conversion Varnish Clear Topcoat
Product Codes:
421-5515 15º Matte
421-5525 25º Low Gloss
421-5535 35º Satin
421-5550 50º Semi-Gloss
421-5590 90º High Gloss
Surface Preparation:
Before application of Plastofix® Light RTS, substrate must be sanded using 120 or 150 grit stearated paper prior to staining or coating. Sealers, if used, should be sanded using #280/320 grid stearated paper and free of dust and all contaminants. Sealers should be topcoated within a maximum of 8 hours of being sanded. Plastofix® Light must not be applied over metal, old oil finish or nitrocellulose lacquers. Stain systems used under Plastofix® Light should be acid stable.
General Information:
Catalyze and reduce material as recommended. To ensure proper sheen, the catalyzed material should be agitated at all times. Apply 3 to 5 wet mils on sanded surface. One or two extra coat can be applied following a complete cure and a sanding with a #280/320 paper. On open pored woods, the best self sealing is obtained by adding a minimum of 50% thinner to the Plastofix after catalyzing. Maximum film build of the system should not exceed 4 mils dry. Plastofix® Light must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats. Avoid all contact with metallic surfaces.
To obtain complete cure, Plastofix® Light must be applied at a temperature above 18ºC and relative humidity below 65%. When drying, this product should not be exposed to ammonia vapors. Finished surface must not be cleaned with ammonia containing products. Always use containers and equipment made of plastic or stainless steel to avoid discoloration of the material due to oxidation.
421-55XX can be used as a self-seal or with following sealers: 390-001, 390-0060, 401-004 catalyzed, 401-028 catalyzed, 431-1219, 432-1220, 546-5192 and 546-8003
PDF Name: CA-PIS_421-55XX_Plastofix_Light_RTS_Conversion_Varnish_Clear_Topcoat
Tack Free Time: 20 - 30 minutes
Files: CA-PIS_421-55XX_Plastofix_Light_RTS_Conversion_Varnish_Clear_Topcoat.pdf
Dry to Sand : 90 - 120 minutes
Dry to Stack: 12 hours
Tack Free Time: Flash off required prior to oven cure
Dry to Sand: 45 - 60 minutes
VOC less exempt g/l: 548
VOC g/l: 548
Dry to Stack: 2 - 3 hours
Note: N/A
Note:
N/A
spec_description:
Plastofix Light RTS is an economical, high quality, self-sealed acid curing Reactive Amino Coating (RAC). Plastofix Light RTS is based on low discolouring resins and contains UV absorbers to make this product light stable. The smooth hardwearing surface shows excellent resistance to mechanical damage, dry heat, household and office liquids, etc.
Special recognition: when applied as specified, will meet required performance for the ANSI/KCMA A161.1 1990 9.0 Finish Test.
spec_uses:
Plastofix Light is recommended for kitchen cabinets, high build office or residential furniture as well as other interior wood applications. Plastofix Light is an all-round coating equally suited for application with roller and curtain coating as well as conventional spraying equipment.
Suggested Uses:
Spray
Mixing Ratio:
8% with 873-0870 or 999-017 by volume
Pot Life: 8 hours
Application Viscosity:
18-20 sec Zahn #2 at 25°C
Reducer: 121-8020 or 121-803
Retarder: 800-5328 EEP
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: 3-5 wet mils
Coverage:
14 m²/l (150 pi²/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #2 signature cup 19 sec at 25°C
Flash Point: 4°C
Density (lb/gal): 0.97 ± 2% at 25°C
Solid (% by weight): 43%
Solid (% by volume): 35%
Shelf Life (months): 12

Plastofix

421-55XX Plastofix® Light RTS Conversion Varnish Clear Topcoat

Find distributor Trouver un distributeur

spec_description:

Plastofix Light RTS is an economical, high quality, self-sealed acid curing Reactive Amino Coating (RAC). Plastofix Light RTS is based on low discolouring resins and contains UV absorbers to make this product light stable. The smooth hardwearing surface shows excellent resistance to mechanical damage, dry heat, household and office liquids, etc.

Special recognition: when applied as specified, will meet required performance for the ANSI/KCMA A161.1 1990 9.0 Finish Test.

BACKRetour

Product codeCodes de produit
Product Codes:

421-5515 15º Matte
421-5525 25º Low Gloss
421-5535 35º Satin
421-5550 50º Semi-Gloss
421-5590 90º High Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 19 sec at 25°C
Flash Point: 4°C
Density (lb/gal): 0.97 ± 2% at 25°C
Solid (% by weight): 43%
Solid (% by volume): 35%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_421-55XX_Plastofix_Light_RTS_Conversion_Varnish_Clear_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more